Hall Limit Automatic Boom Barrier DC Motor Brushless Speed Adjustable Arm Auto Reverse
Brand Name:WONSUN
Certification:CE
Model Number:DZ-220
Minimum Order Quantity:1PC
Delivery Time:3-7 working days after received your payment
Payment Terms:T/T,Western Union,Money Gram, Trade Assurance,Paypal etc.,
Contact Now
Add to Cart
Verified Supplier
Location:
Shenzhen Guangdong China
Address:
1st Floor, Zhigu, No. 2-10, South jinlong Avenue, Shahu Community, Biling Street, Pingshan District, Shenzhen, China
Supplier`s last login times:
within 25 hours
Product Details
Company Profile
Product Details
Hall Limit Automatic Boom Barrier DC Motor Brushless Speed
Adjustable Arm Auto Reverse
Features
1 The running speed can be adjusted from 1.5s to 8s
3 Open the barrier gate by motor wheel when power off ,automatically reset after power on
4 Curved crank arm three- link movement structure, the operation is stable
5 Wireless remote control control open/close
6 Auto reverse function(force adjustable)
7 Infrared photocells connector is available
8 Loop detector connector is available.
9 Well-integrated with car parking system equipment,with wire control(must be switch signal)
10 Connector for traffic light(AC220V,power less than 40W)
11 Offering dry contact signal for car parking system(COM,NC,NO)
12 Auto-delay when closing(adjustable)
13 RS485 or CAN network communication interface(no need to install module)
14 Counting interface
15 24V backup battery interface(Can be charged by using solar energy)
Technical parameters
1 Working temperature(motor): -35℃~+85℃
2 Rated voltage:DC24V
3 Running speed:1.5s-8s
4 Rated current:8.58A
5 Rated power:140W
6 No-load speed:1850rpm
7 Rated speed:1400rpm
8 Output Power:56.8N.m
9 Relative humidity:≤90%
10 Remote control distance:≤100M(in the open place)
11 IP Degree:IP44
12 Max length of arm:6M
Installation, commissioning and use
7.1 Equipment installation
7.1.1 Please select the correct type of barrier gate according to the specifications of
the pace,and then fix the barrier cabinet with expansion bolts(refer to Figure 3).
After determined the position,the barrier gate foundation should be done according to the site conditions,and
also make the cast-in-place basement for the non-concrete ground.
7.4 Adjust the Position of Barrier Arm
To adjust the position of the arm (for example, after exerting excessive force), please take the steps as below:
- open the barrier gate door and remove the cover
- loosen the two fasten screws of the DZ-1 on the boom shaft with the M12's Allen wrench, so that the boom can be re-positioned by hand.
- adjust the position of the boom (horizontal position, as shown in picture 1).
- Use the hexagonal wrench to tighten the two fastening screws (72 Nm)
The parameter for selecting the balance tension spring
| Arm Type | The Length of arm | Selection Spring | |
Type | Spec.(diameter*Length) | ||
| Straight Arm/Folding Arm | 6M≥L＞5M | Extension Spring | (ø5.5x280)+(ø4.5x280) |
| 5M≥L≥4.5M | (ø5.5x280) | ||
| 4.5M＞L≥3M | (ø4.5x280) | ||
| Fence Arm | 5M≥L≥4M | (ø6.5x280)+(ø6.5x280) | |
| 4M＞L≥3M | (ø5.5x280)+(ø4.5x280) | ||
(the parameter is based on the company’s arm)
Wonsun is a professional manufaturer for barrier gate, boom
barrier, sliding gate motor. If any interest, please contact me
freely.
Hall Limit Automatic Boom Barrier DC Motor Brushless Speed Adjustable Arm Auto Reverse
Inquiry Cart
0