high accuracy single-channel analog signal to RS485/RS232 A/D converter(4-20mA/0-10V/0-5V to RS232/RS485 A/D converter)

high accuracy analog signal to RS485/RS232 A/D converter Features and Applications:
● Analog signal acquisition, isolated RS-485/232 output
● 12-bit AD converter, testing accuracy>0.1%
● Can be remotely reconfigured for modules accuracy by RS-485/232 Interface
● Three-port isolation (input/output/power supply): 3000VDC /60s
● Wide operating power supply: 8~32VDC
● High reliability, easy programming and installation
● International standard DIN35mm rail mounting for easy centralized wiring
● Can Program setting module address, baud rate , etc.
● Supports Modbus RTU
● Low cost, small size modular design
● Analog signal testing/monitoring/control
● RS-485 remote I / O, data acquisition
● Intelligent building control, security engineering and other applications
● RS-232/485 industrial automation control system
● Industrial field signal isolation and long-term transmission
● Monitoring equipment operation
● sensor signal measurement
● Industrial data acquisition and recording
● medical, industrial product development
● 4-20mA/0-5V or 1-5V signal acquisition

high accuracy single-channel analog signal to RS485/RS232 A/D converter(4-20mA/0-10V/0-5V to RS232/RS485 A/D converter) Product Selection:

Sample 1: Model: JSD AD11-I4-485 4-20mA input,RS485 interface output

Sample 2:Model :JSD AD11-V2-232 0-10V input, RS-232 interface output
Sample 3:Model :JSD AD11-V1-485 0-5V input, RS-485 interface output
Sample 4:Model :JSD AD11-V3-232 0-75mV input, RS-232 interface output

JSD AD11–V(I) □ – □

Input Voltage or Current Signal Interface

V1:0-5V 485: output is RS-485 interface

V2:0-10V 232: output is RS-232 interface

V3:0-75mV

V4:0-2.5V

V5:0-±5V

V6:0-±10V

V7:0-±100mV

Vud:user-defined

current/voltage signal to RS485/RS232 A/D converter General Description:
JSD AD11 series products realize the signal acquisition between sensor and host, to measure analog signals. JSD AD11 series products can be applied to RS-232/485 bus industrial automation control system, 4-20mA / 0-5V signal measurement, monitoring and controlling, 0-75mV, 0-100mV and other small-signals measurement and signals isolation and long-term industrial transmission and so on. Products include power supply isolation, signal isolation, linearization, A/D conversion and RS-485 serial communication. Each serial interface can connect up to 255 pieces JSD AD11 Series modules, communication using ASCII code or MODBUS RTU communication protocol, and its instruction set compatible with the ADAM modules, baud rate can be set by the code, with other manufacturers control module hang in the same RS-485 bus for easy programming
JSD AD11 series is based on SCM intelligent monitoring and control system, all of the users set configuration information such as Calibration value, address, baud rate, data format, checksum and status are stored in non-volatile memory EEPROM.
JSD AD11 series products according to industry standard design and manufacture .They are three-port isolation(input, output and power supply),and the isolation voltage between them is up to 3000 VDC, JSD AD11 series products have better Anti-interference ability, high reliability and wide operating Temperature Range (- 45℃～+85℃.)

A/D converter General parameters:

(typical @ +25 ℃, V s to 24VDC)

Input type: current / voltage input

Accuracy: 0.1%

Temperature drift:± 30 ppm / ℃ (± 50 ppm / ℃ max)

Input Resistance: 50Ω (4-20mA/0-20mA/0- ± 20mA current input)

100Ω (0-10mA/0- ± 10mA current input)

1KΩ (0-1mA/0- ± 1mA current input)

>1MΩ(voltage input)

Bandwidth: -3 dB 10 Hz

Conversion rate: 10 Sps

Common Mode Rejection (CMR): 120 dB (1kΩ Source Imbalance @ 50/60 Hz)

Normal Mode Rejection (NMR): 60 dB (1kΩ Source Imbalance @ 50/60 Hz)

Input Protection: over-voltage protection, over-current protection

Communication: RS-485 protocol or RS-232 , standard characters protocols and MODBUS RTU communication protocol

Baud Rate (1200,2400,4800,9600,19200,38400 bps) can be selected via software

Address (0 to 255) can be selected via software

Communication Response Time: 100 ms maximum

Power Supply: +8 ~ 32VDC wide range power supply, internal anti-reverse and over-voltage protection circuit

Power Loss: less than 1W

Operating Temperature: - 45~+80 ℃

Operating Humidity: 10 ~ 90% (no condensation)

Storage Temperature: - 45~+80 ℃

Storage Humidity: 10 ~ 95% (no condensation)

Isolation Voltage: input / output: 3KVDC/1 minute, leakage current:1mA

Which output signal and power supply are common ground.

Shock Voltage: 3KVAC, 1.2/50us (peak)

Notes:

1,NC" pin must not be connected to any external circuit, otherwise it will damage the product itself;

2,Please read the user manual carefully before using. If any question please contact our technical support department.

3,Please do not use this product in hazardous area. The power supply of this product should be 24VDC power source. It is forbidden to use 220VAC power supply.

4,Calculating from the date of delivery, during normal use of the product, any quality problems are free repair or replacement by Company during 3 years warranty,

5,the product is strictly forbidden demolish without permission for not damage

6,All specifications measured at Ta=25°C, humidity<75%, nominal input voltage and rated output load unless otherwise specified.

7,In this datasheet, all the test methods of indications are based on corporate standards.

Dimensions: 115 mm x 100 mm x 23mm

A/D converter product picture and Dimensions:

Shenzhen Jieshengda Technology Co., Ltd. is a is a high-tech enterprise for dedicating to professional R&D isolated transmitter, isolation amplifier,4-20mA Isolation Amplifier,active two-wire isolation amplifier, active isolation amplifier (optocoupler isolation and magnetic isolations), mV-level isolation amplifier, isolation power transmitter, PT100 RTD temperature transmitter,signal isolation transmitters, power isolation transmitter, fence, V/F frequency isolation transformer, resistors，switch signal isolation transmitter, pressure transmitter,F/V frequency isolation transmitters, non-isolated amplifier, data acquisition, AC-DC converter ，DC-DC converter, high-voltage converter, Medium-power converter, micro-power DC-DC converter, LED lights. Self-developed products meet international standards, products performance reliability and passed EMC Certification (CE certification), the input and output signals are adopting international standard signal designs. (eg: 0~±20mA/0~10V/0~20mA/0~5V/4~20mA/1~5V/0~±10mA/0~±10V, etc.) compatible with the vast majority of domestic and foreign well-known brands ,our products categories covering more than thousands, is industrial automation applications analog signals, digital signals hybrid integrated circuit development, and manufacturing companies.

By all the people’s unremitting efforts ,our products has been widely used in the electricity, telecommunications, instrumentation, industrial measurement systems, medical equipment, industrial intelligence, intelligent cars, intelligent building control, automotive electronics, security, environmental protection, food, heating and air conditioning systerms, water treatment, petrochemical, coal mining , metallurgy, shipbuilding, military and other fields , At the same time providing hidh quality products to customers in different areas, to provide different functions of products, to offerr customized products, to provide customers with a reasonable solution and so on.

Jieshengda establish a "people-oriented, customer first, forge ahead, and common development" for business purposes, "honesty, pragmatism, dedication, innovation" for management philosophy, the company relies on technology and development, and constantly provide customers with high-tech products, is up to people of all Jie Sheng constant pursuit. Continue to provide users with high-tech products is Jie Sheng da techonology constant pursuit

Today ,Jieshengda pursuing "rigorous and realistic progressive unity", continuous innovation, "technology as the core, depending on the quality of life, with action to prove", dedicated to providing high quality products, at the same time to provide you with the most professional one-stop service.