EPM3064ATC44-10N power ic chip ic components Programmable IC Chips Programmable Logic Device Family

MAX 3000A Programmable Logic Device Family

Features
■ High–performance, low–cost CMOS EEPROM–based programmable logic devices (PLDs) built on a MAX® architecture
■ 3.3-V in-system programmability (ISP) through the built–in IEEE Std. 1149.1 Joint Test Action Group (JTAG) interface with advanced pin-locking capability – ISP circuitry compliant with IEEE Std. 1532
■ Built–in boundary-scan test (BST) circuitry compliant with IEEE Std. 1149.1-1990
■ Enhanced ISP features: – Enhanced ISP algorithm for faster programming – ISP_Done bit to ensure complete programming – Pull-up resistor on I/O pins during in–system programming
■ High–density PLDs ranging from 600 to 10,000 usable gates
■ 4.5–ns pin–to–pin logic delays with counter frequencies of up to 227.3 MHz
■ MultiVoltTM I/O interface enabling the device core to run at 3.3 V, while I/O pins are compatible with 5.0–V, 3.3–V, and 2.5–V logic levels
■ Pin counts ranging from 44 to 256 in a variety of thin quad flat pack (TQFP), plastic quad flat pack (PQFP), plastic J–lead chip carrier (PLCC), and FineLine BGATM packages
■ Hot–socketing support
■ Programmable interconnect array (PIA) continuous routing structure for fast, predictable performance
■ Industrial temperature range

■ PCI compatible
■ Bus–friendly architecture including programmable slew–rate control
■ Open–drain output option
■ Programmable macrocell flipflops with individual clear, preset, clock, and clock enable controls
■ Programmable power–saving mode for a power reduction of over 50% in each macrocell
■ Configurable expander product–term distribution, allowing up to 32 product terms per macrocell
■ Programmable security bit for protection of proprietary designs
■ Enhanced architectural features, including: – 6 or 10 pin– or logic–driven output enable signals – Two global clock signals with optional inversion – Enhanced interconnect resources for improved routability – Programmable output slew–rate control
■ Software design support and automatic place–and–route provided by Altera’s development systems for Windows–based PCs and Sun SPARCstations, and HP 9000 Series 700/800 workstations
■ Additional design entry and simulation support provided by EDIF 2 0 0 and 3 0 0 netlist files, library of parameterized modules (LPM), Verilog HDL, VHDL, and other interfaces to popular EDA tools from third–party manufacturers such as Cadence, Exemplar Logic, Mentor Graphics, OrCAD, Synopsys, Synplicity, and VeriBest
■ Programming support with the Altera master programming unit (MPU), MasterBlasterTM communications cable, ByteBlasterMVTM parallel port download cable, BitBlasterTM serial download cable as well as programming hardware from third–party manufacturers and any in–circuit tester that supports JamTM Standard Test and Programming Language (STAPL) Files (.jam), Jam STAPL Byte-Code Files (.jbc), or Serial Vector Format Files (.svf)

Functional Description
The MAX 3000A architecture includes the following elements:
■ Logic array blocks (LABs)
■ Macrocells
■ Expander product terms (shareable and parallel)
■ Programmable interconnect array (PIA)
■ I/O control blocks

The MAX 3000A architecture includes four dedicated inputs that can be used as general–purpose inputs or as high–speed, global control signals (clock, clear, and two output enable signals) for each macrocell and I/O pin. Figure 1 shows the architecture of MAX 3000A devices.

Figure 1. MAX 3000A Device Block Diagram

Note: (1) EPM3032A, EPM3064A, EPM3128A, and EPM3256A devices have six output enables. EPM3512A devices have 10 output enables.

MAX 3000A Device Absolute Maximum Ratings

Note:
(1) Minimum DC input voltage is –0.5 V. During transitions, the inputs may undershoot to –2.0 V or overshoot to 5.75 V for input currents less than 100 mA and periods shorter than 20 ns.


Stock Offer (Hot Sell)

King--- Originator of ANTERWELL, engaged in the IC electronics industry in 1998 and establish ANTERWELL in 2004. The company is located in Shenzhen Huaqiang North, the largest electronic center in Asia. Our main business is the technical development and electronic products import and export business. Currently, we have branches in Hong Kong and Malaysia.

Up to now. ANTERWELL have more than 1,000,000 types of electronic components in stock. ANTERWELL has become one of the top choices for purchasing IC chips both domestically and internationally. King is a senior IC chip expert, sales engineer, and mentor, leading an elite team with customer first, quality first, honesty, trustworthiness, and mutual benefit. We look forward to cooperate with you to create a better future!

ANTERWELL’s main products include semiconductors, resistors, capacitors, diodes, inductors, connectors, transistors, sensors, etc. Involving the major well-known brands such like: TI, XILINX, FAIRCHILD, STM, MICRON, MICROCHIP, TDK, SAMSUNG, ON, NXP,IR,ADI, ATMEL,VISHAY,LINEAR etc.

ANTERWELL adheres to the development concept and purpose of "direct stock offer, excellent quality, favorable price, and sincere service", which is deeply recognized by domestic and foreign customers. Based on the long-term development goal, ANTERWELL provides customers with standardized, professional, and diversified high-quality services through a strong market service network. ANTEWRELL has multiple skilled and capable executives with a professional QC team and excellent sales team to win the high support and trust of the vast customer base! We provide the best quality, price and service.

ANTERWELL will be your best Partner.