0~200mv Light Weight Load Cell Meter 32 Bit CPU For Film Slitting Machine Tension Meter For True Engin
Brand Name:True Engin
Certification:ISO9001
Model Number:STM-10PD
Minimum Order Quantity:1 unit
Delivery Time:1~3 days
Payment Terms:T/T, L/C, Western Union
Contact Now
Add to Cart
Active Member
Location:
Wuhan Hubei China
Address:
Room D-011 No. 517 Ming-ze Peninsula Luoshi South Road, Hongshan District, Wuhan City
Supplier`s last login times:
within 41 hours
Product Details
Company Profile
Product Details
0~200mv Light Weight Load Cell Meter 32 Bit CPU For Film Slitting Machine Tension Meter For True Engin
Tension Detector Intelligent Tension Meter For Tension Load Cell In Flim Slitting Machine
Features:
1. 32 Bit CPU guarantees high speed,precision,anti-jamming
capability and ensures reliability.
2. The outside has no adjustable potentiometer.
3. 0~10V /0~5V and 0~20ma/4~20ma output signals can be free to
choose.
4. Use dispensing technology, small volum,light weight.
5. Mosaic installation,simple and convenient.
Attention:STM-050 tension meter only display tension,no control signal output,other functions same as STM-10PD.
| Parameters | |
| Model | ST-10PD |
| Power Supply | DC 24V |
| Input Analog singal | 1. L+~L-;R+~R-;Left,right tension loadcell signal input |
| STS tension loadcell signal (0~200mv,power supply DC5V) | |
| STSA tension loadcell signal(0~15mv;power supply DC5v) | |
| Control output | 1. Vout-GND:DC0~10V/0~5V |
| 2. Iout-GND:DC0~20mA/4~20mA | |
| (STM-050 without Vout,Iout output) | |
| Tension Display | L+R Total tension L: left tension R:right tension |
| Fixed output | 5V+-GND:DC5V tension loadcell power supply |
| Outline size | 96*48*109mm |
Electrical Wiring
L+:positive terminal of tension detector input signal on left side
L-:negative terminal of tension detector input signal on left side
5V+:positive terminal of tension detector power supply on both sides
PE:detector shielding cable on both sides
GND:power supply negative terminal on both sides
R+: positive terminal of tension detector input signal on right side
R-:negative terminal of tension detector input signal on right side
STS sensor wiring
Iout: 0~20mA output
Vout: 0~10V output
5V+: 5V output
GND: output negative terminal of voltage and current
NOTE:
(1) If STM-10PD tension meter install STS Differential sensor by wuhan true engine company ,wiring colors as follows :
(2) If STM-10PD tension meter install STSA Strain-gauge sensor by wuhan true engin company ,wiring colors as follows :
“5V”—red “GND”—black, “Terminal +”—green, “Terminal-”—white,
(3) If only use one tension sensor,please use wires to connect L+ with R+,L- with R-.
“5V”—red “GND”—black, “Terminal +”—green, “Terminal-”—white,
Romove faults
1. The mass of detected reel is too large,the rated value of the tension detector is too small,both will cause the fault alarm of signal is too large.
2. C11 parameter value is not match with the actual tension sensor type,it will cause the fault alarm of signal too large or signal too small.
3. The wrap angle of film overt detector reel is too large,the force caused by film tension point to the screw ends of tension detector,ot will cause the fault alarm of signal is too small.
4. The tension sensor connect is not correct,fropped or damaged,left amd right pressure is imbalance,it will cause the fault alarm.
5. The load id too large will caused the fault alarm of "more than limit‘
Zero calibration
Machine power off, there is no film or film is loose.
Enter C01 parameter screen,press button can change C01 from 0 to 1,when it change from 1 to 0 automatic,zero calibration is completed.
After zero calibration,if up LED displays error and alarm indicator lightens,refer to section7, 8 for the problem.After trouble is remove,return C01 to zero calibration.
Span calibration
Machine power off.Thread a string through the reeler center like what the material does during the actual operation.Hang weights on the end of the string while the other end is fixed well.
The weights should be more than half of the rated measurement range of the detetor.
Enter C02 ,use , button to change its value to be equal to the hanged weight in Newton.
Enter C03,press button,change its value from 0 to 1,when 1 change to 0 automatic,span calibration is completed
After span calibration,if up LED displays error and alarm indicator lightens,refer to section7, 8 for the problem.After trouble is remove,return C03 to span calibration.
FAQ
How to get your suitable machine parts
Enquiry: Contact us by email, phone call, fax, Instant Messenger
(Skype) and let us know your enquiry.
Discussion:Let us know the model number,like magnetic powder
clutch, specify the items you desire, confirm specification;
OEM/ODM consultation.
Place order as per contract or discussion.
Perform invoice( sales contract ) In duplicate confirmed and kept
by both sides.
Payment settled.
Order completed under our arrangement.
Goods shipped as per contracted term.
Goods arrive at local port or warehouse, depending on contracted
term.
Support & re-ordering.
Any question about Printing Machinery Parts ,contact with us
please,sincere service for you and welcome to Micro Control!
0~200mv Light Weight Load Cell Meter 32 Bit CPU For Film Slitting Machine Tension Meter For True Engin
Inquiry Cart
0