Product Details
SFC-IEC-A1B series 5 to 14" 15Amp Hardwired Power Strip with 10 Outlets
This hard wired type power strip is good for installation in your
kitchen, cabinet, on the rack and so on. It is not for normal wall
outlets. There is no power cord and plug with this unit.
Features
- 5" to 14” - Durable Aluminium alloy Metal Housing Power Strip
- 2 Black ( white or grey or other) US NEMA 5-15R Outlets, Vertical or
level Outlet Orientation
- Hardwired without Power Cord for Mounting at Your Desired Location
- One IEC C 14 Input on Each Side - (on the Top or Bottom Cover or Both Sides or Ends)
- Electrical Ratings: 100-125V 60Hz 15A
- UL C-UL Approved and Listed
- Outlets 0.12" to 8.39" (3mm to 213mm) apart center to center
- With IEC C13 Cable Easier put in C14 inlet and Faster Installation
- Higher Efficiency
| |
Model #: | SFC306-1013-IEC |
Description: | 5 to 14" 2 Outlet Hardwired Power Strip |
Power Strip Measurement: | L5 to14" x W1.614" x H1.255" (133 to 355 x 45 x 42) * |
Outlets: | 10 |
Outlet Color: | Black, white, grey or other |
Outlet Orientation: | Vertical or level |
Receptacle Type: | NEMA 5-15R |
Outlet Spacing: | 0.12to 8.39" (3 to 213mm) (center to center) |
IEC C14 Inlet: | on Top or Bottom Cover or Both Sides or Ends) |
Voltage Input/Output: | 110-125V 60Hz |
Current Input: | 15A |
Full Load: | 1875VA |
On/Off Switch: | Yes |
Circuit Breaker: | 15A |
Surge Protection: | N/A |
Indicators: | Yes |
Mounting Tabs: | On both ends or bottom |
Mounting Clips: | Mounting Clips included |
SAFETY WARNING:
Installation work of this unit must be done by a professional, a
licensed electrician or an electric engineer.
Never install this unit during a thunder storm.
Switch off the power before you start installation work.
This unit is for indoor use only.
This unit is not intended for use in or around wet or potentially
wet areas including, but not limited to, aquariums, saunas, showers
and fountains.
Risk of Electric Shock!
INSTALLATION GUIDE:
Before installation, you may need to get a IEC C13 Outlet. Decide
your wire gauge, and ask store attendant for assistance what color
of connectors you should get) from your local hardware or electric
supply or home improvement stores.
Minimum tools required: A fine to medium fine philips screw driver,
and a pair of scissors, and a pair of mid size slip joint pliers
1. Turn off electricity in the house
2. Decide where to place this unit
3. Choose the side you want the cord exit to choose IEC C14 Built
in power strips
4. Match the color of the wires and secure the wire connection with
proper wire connectors built in IEC C13 plug.(different wire gauge use different colored wire connectors)
- Mount the power strip where you want it to be:
A) For power strips with mounting tabs on both ends: screw down the
unit on the floor, wall or in your cabinet or on your rack, where
you want it to be
B) For power strips without mounting tabs, but to be mounted with
clips, place the unit where you want it to be first, make marks
where to install the clips, which normally should be placed about
min 2”<power strips length away from each end, and then screw
the clips down with screws provided. Then, snap the power strip in
on the clips - Push IEC C13 outlet plug into IEC C13 inlet power strips , and push
switch to ON. Turn electricity back on, you are ready to go.
Note:
We also custom manufacture for our customers.
Company Profile
Jiashan Dingsheng Electric Co., Ltd. is Located at Jiashan, which is at the north end of the first
cross-sea bridge in the world and combination of
Jiangsu,ZhejiangandShanghai. This area develops fastest in the east
ofChinaand has most convenient transporta -tion (It is80 kmfar
fromShanghai,110 kmfromHangzhouand100 kmfromSuzhou). Sheng feng has
been devoted to develop, design and produces: switches, socket,
Power strips, Push to open (push to exit) etc for electrical
appliance manufacturer, and using in rack mount, raceway, laptops
cart and workbench applications etc.
( Our products are exported to developed countries in Europe
andAmericadirectly or indirectly. We could develop new products
accord to the functional requirement and assembly requirement or
drawings of clients for special products.)
The company has mainly become to develop and produce special or
replace imported products for clients. The products has won trust
and affirmation of many clients, got ISO9001 and UL, c-UL, ITS-BS,
RCM ,CE certificate and is applying other international
certificates such as TUV , and self-export rights. We will make
efforts as usual to improve products, ensure the quality of
products and make products more excellent. Our service aim is to
become pioneer of market with pragmatic business style, concept of
integrity services, and on the base of scientific and technological
innovations. We are willing to cooperate closely with various
vendors at home and abroad, seek common development and advance
with the times. Welcome you to visit our factory and supply your
advice.
You can find a product with best price and quality here.