Anti Clogging Rectangular Floor Drain Grate Fast Drainage No Mechanical Durability

Customized Stainless Steel Floor Drain For House Construction And Project Building

About stainless steel floor drain

• The floor drain should have four characteristics: fast drainage, anti-odor, anti-clogging, easy to clean.
• Floor drains, floor drains, as the name implies, are leaking, and the single function of leaking the floor drain has not kept up with the times.
• The floor drain not only has to be launched quickly, but the most important thing is to prevent blockage. Otherwise, if it is old, it will be infinite.

Stainless steel floor drain selection points

• Water seal is one of the important features of water seal floor drain. When selecting, you should know whether the water seal depth of the product reaches 50mm. Side wall type floor drain, with frame floor drain, closed type floor drain generally do not have water seal; anti-overflow floor drain, multi-channel floor drain mostly with water seal, should be clearly understood according to the manufacturer's information when selecting.For drains without water seal, the depth of the drain seal should be no less than 50mm. This component can be configured by the floor drain manufacturer or by the construction unit where the floor drain is installed.
• The height of the floor drain rafter can be adjusted, and the height adjustment is not less than 35mm to ensure that the floor drain surface level and the ground level after the ground decoration is completed. The waterproof wing ring is provided for the floor drain to ensure the waterproofing of the floor drain when it is installed on the floor.The floor drain of an underground garage car passage or a load-bearing place shall have the strength of the rafter to meet the corresponding load.
• The structure of the drain with water seal should be reasonable and smooth, and the debris in the drainage is not easy to settle; the cross-sectional area of ​​the cross section of each part should be larger than the cross-sectional area of ​​the discharge pipe, and the minimum net width of the cross section of the flow channel should not be less than 10mm.
• There are three ways to connect the floor drain: socket; thread; clamp. The size of the connection port can be determined according to the relevant regulations of the current country.
• Deodorant floor drain should be preferred, and floor drains should not be provided where drainage is not required. The builders have not set up a leak in the backwaters and must not be completed.

Stainless steel floor drain installation

• Installation

First: Trim the reserved hole of the drainage to make it completely coincide with the floor drain that was bought back, because the reserved hole for drainage by the real estate agent when the house is delivered is relatively large. Among them, the opening aperture of the floor drain tweezers should be controlled between 6-8mm, which can prevent the entry of hair, sludge, sand and other contaminants;
Second: It should be grasped that the multi-channel floor drain inlet is installed according to the actual situation. The multi-channel floor drain is a floor drain with a multi-functional joint that can accept (washer, bathtub, washing machine and floor drain). This structure can solve the problem of requiring multiple drainages for a sewer.

• Retrofit

There are two ways to add a floor drain in a place where there is no floor drain: one is to raise the ground and lay down the water pipe; the other is to break through the floor and re-route the water pipe.

Stainless steel floor drain basic introduction

• The floor drain is a drainage device connected to the ground and the drainage pipe system.
• The special features of the floor drain: it excludes ground water, water stains, solid objects, fibrous materials, hair, and easy deposits.
• The main function of the floor drain: Odor-proof, anti-blocking, anti-mite, anti-virus, anti-backwater, anti-dry (mainly refers to water-sealed floor drain)
• The quality of the floor drain is mainly reviewed from four angles: drainage speed, deodorization effect, easy cleaning, and no mechanical durability.

Our projects

Our Shenzhen production base is about 8000 square meters, Dongguan Industrial Park is about 50,000 square meters, and there are 50 advanced stainless steel material processing equipments such as CNC machining centers, laser cutting machines, CNC routers, etc.

There are about 280 employees (factory production staff 200 people). 80 project construction staff, among which there are 50 senior technicians with rich working experience.

The company is mainly engaged in the finishing of stainless steel plates, stainless steel honeycomb plates, anodized aluminum plates, copper plates and other metal plates in the architectural decoration industry.

The annual output of stainless steel is 256,000 square meters, and the finished product rate reaches 85%. The project's performance has spread all over the country.

In addition, it has also participated in the construction of many large-scale projects in the Middle East,Europe and Americas