61 Watts Mini Water Cooler Dispenser 85-95 Degrees Centigrade Small
Cute Appearance with good sales on Amazon. To get more know
products information, please visit the below link on Amazon from
one of our UK customers.
https://www.amazon.co.uk/dp/B078XBL9HJ
https://www.amazon.co.uk/dp/B01NAP7OU5
Products component checklist :
Number | Products Description |
1 | Filter change indicator |
2 | Unfiltered water chamber |
3 | Filter cartridge |
4 | Indicator light |
5 | water tap |
6 | Drip tray |
Technical and Replacement filters
| System Specification |
Electrical Requirements | 220 - 240V , 50/60 Hz |
Input cooling | 61 Watts |
Filter replacement model | |
Filter cartridge life | 150 litres or 2 months |
Filter cartridge flow rate | 100-400ml/minute |
Filter reduction capabilities | Chlorine, lead, copper, etc |
Products weight | 3.2 KGS |
Total water tank capacity | 8.5L |
Filtered water tank capacity | 5L |
Unfiltered water tank capacity | 3.5L |
Sterilising and Cleaning Instructions
It is important to follow the sterilising and cleaning process
below before using and as part of your regular maintenance routine:
- Combine two tablespoons of baking soda with 2 litres of lukewarm
water in a separate container
- Remove the unfiltered water chamber from the cooler
- Pour the bicarbonate solution into the water chamber
- Press the water dispenser until water pours from the tap
- Cycle the bicarbonate solution through the tap and empty into the
top water chamber, Repeat this procedure several times
- Turn on the power and leave for at least 4 hours
- Drain all the bicarbonate solution until empty
- Remove the drain plug from underneath the unit to drain any water
or solution in the cooling tank. This is vital to ensure the solution is expelled from the cooler
- While the drain plug is open, rinse the unit with 2 litres of clean
water to remove any bicarbonate solution
- Refit the top and water chamber
- Flush clean water through the unit and drain out via the tap, Tilt
the unit forward and backward to expell all water from unit
Products simple operation introduction :
Before first use :
- Wash and rinse out the plastic water tanks thoroughly before use
- Remove the filter from its packaging then fully cover and soak in
cold clean water for approximately 15 - 30 minutes then rinse off
under cold clean running tap water until see the clear water then
will start for using
- You may notice a fine black dust come out of the filter, this will
happen on all new filters and when water is filtered through it the
first couple of uses . This is no cause for alarm . It is just the
dust from the activated carbon inside the filter. Although it looks
unsightly , it will not harm you.
Prepare Filter
- Remove filter cartridge from plastic cover
- Do not lose the filter cartridge O-Ring
- Soak filter cartridge in water for approximately 20 minutes
- Shake filter while under water to remove dark carbon particles and
any trapped air
Insert filter and ensure it sits flat and fully seated
Assembly:
- Ensure Drain Plug underneath unit is secure on the unit
- Place unfiltered water chamber on to the Filtered Water Chamber
- Place Filter cartridge into the unfiltered Water Chamber. Ensure
Filter cartridge is secure
- Place top on top of water Chamber
- Turn the switch to "ON" at the back of the unit
- Empty water into the unfiltered water chamber, allow water to run
through to the Filtered water Chamber
- Once the Filtered water chamber is filled, push and hold the tap
down until water comes out of the tap
When you turn on the switch to " on" at the back of the unit , you
will see RED LIGHT indicating the water
cooler is chilling the water . When the indicator light from RED
LIGHT to BLUE LIGHT indicating the water
approximatly 800ml cold tank has fully chilled .
Red Light : Water is chilling
Blue Light: The water has fully chilled for drinking
Technical and Replacement filters
Maintenance :
- Replace filter after 150 litres or 2 months of use or whichever
comes first
- If the taste , smell or flow rate changes , it is recommended you
change the filter immediately
- Sanitise the unit fully every 1 to 2 weeks. This will be based on
the customers' requirement.
Notices :
If the water cooler has not been used for some time , unplug the
unit , drain all the water and clean with warm soapy water .
Flush the water cooler and empty all water out through the water
tap or tearing out the bottom small
silicone tube |
Position :
- The unit is designed for light use at home or in a small office
- If the unit is damaged in any way , refrain from using it
- Keep away from direct sunlight
- Ensure the unit is appropriately earthed
- Ensure the unit has 100mm of ventilation all round
- Do not place near a heat source
Contact details:
NINGBO GOOD WATER SOURCE ENVIRONMENTAL PROTECTION ELECTRICAL
APPLIANCE CO.,LTD
CONTACT PHONE(WHATSAPPLE): (86) 13884494576
CONTACT E-MAIL: jackliu@miniwatercoolerdispenser.com
WECHAT: Jackliu8886
SKYPE: jackliu06316
Besides, to get more know products information, please visit the
below link on Amazon from one of our UK customers
https://www.amazon.co.uk/dp/B078XBL9HJ
https://www.amazon.co.uk/dp/B01NAP7OU5