Lightweight S Trap Toilet Waste Pipe Connector / 90 Pan Connector White Color

The toilet drain pipe wall row to row the Australian PVC pipe toilet seat shifter

The drainage pipe diameter of the toilet is according to the national standard, the minimum diameter is the sewage pipe of DN100, and now it is generally used with u-pvc pipe, and the minimum diameter is de110.2. If you are in your own home and are subject to the height of the ground, you can also use the u-pvc tube with a smaller de75.Generally, the size of the toilet drain is 5 to 6 cm, and the toilet S bend is usually 5 to 6 cm.The size of the sewer pipe is generally about 110 cm.

Nowadays, every household must have the bathroom equipment -- toilet, how to install?Generally speaking, the installation of the flush toilet more professional, is to provide services by merchants in the stores, if there is no special instructions, freight and installation fee included in the purchase and payment, you help a friend pay attention to, be sure to check before installation implement trace of usefulness, it is better that some implement have water, may be during the inspection, do not matter.
Installation of a flush toilet drain pipe.
1. The waste pipe of the toilet shall be smooth, flat, free of air bubbles, no cracks, no visible specks and sag in the inner wall of the plastic pipe materials required by the national standards.How are flush toilets installed
2. The pipe in the urinal has been set apart from the stench, so there is no need to set the water trap on the sewage pipe, otherwise it will affect the function of the toilet flushing.
3. Drain connection horizontal tube and vertical tube connection, should use 445 degrees 5 ° inclined well were connected is advisable.
Installation steps of flush toilet.
1. Determine the installation position and hole in the ground to the ground at outlet of drain pipe and the bottom of the toilet bowl, according to the outside of the flush toilet base size, draw the toilet on the ground points of fixed position of the hole, and impact drill holes.The hole depth is about 5 cm.
2. Install the steel expansion bolt into the ground drilling with the pedestal of the flush toilet seat, insert the bottom corner of the toilet into the expansion bolt and tighten the nut to put the toilet in place.The toilet drain is tightly connected with the ground preset drain pipe and sealed.3. Install the tank (even toilet doesn't need this step) according to the installation height and water tank on back wall perforation position, the corresponding fixed position on the metope of drilling and tapping into the steel bolts, then put the water tank in place, make the back wall perforation sets into the expansion bolt, add 3 mm thick nylon washer on the nut and tighten.
4. Install the connecting pipe between the water tank and the toilet seat (with copper pipe or plastic pipe, etc.), and the connecting pipe between the inlet pipe and the bottom of the tank (with stainless steel bellows, etc.).Inlet connection should be equipped with Angle valve (inlet valve).
5. Install floating ball and other accessories in the water tank.
6. After opening the water inlet valve, the height of the floating ball shall be adjusted according to the water inlet height required in the water tank, and the tightness of its control screw shall be adjusted according to the water spraying valve size.
7. After the tank is filled with water, check the toilet drain capacity, and whether there is leakage in the connection of each pipe.
8. Seal the gap between the toilet seat and the floor with putty or silica gel.Cement mortar or cement mortar shall not be used as sealing material.
Install toilet seats and toilet seats.In addition, each house has a different flush toilet to install the hole pitch, before buying the toilet, must let the worker help you plan to measure well, otherwise very likely the toilet that buys is installed not to go up.Flush the toilet after the installation is complete, in the first place to try flushing effect, the best way is: find a cigarette butts thrown into, can just ran down, and the voice is not big, the install link no problem.
The above is all about how to install the toilet bowl, the information is for reference only!

Xiamen MuRuJia CO., LTD., founded in 2015,we are one professional company who supplies all kinds of bathroom products,like Toilet Tank Fittings,Toilet Seat Covers,Plastic & Brass Bidets, SS Bidets,Hand Shower ,RainShower and Shower Kits,Brass & Plastic Faucets,SS/PVC Shower Hoses,all kinds of Drainer Pipes,Plumbing Rubber & Seal,Installation Screws.Our products are covering all over the world!

Welcome to visit our company.

Hopefully we will have chance to serve you the best.