2‘’-8‘’ steel pipe with big diameter bending machine to bend section steel into different radian

The arch bending machine bends various profiles into different arc radii

一, Brief introduction of GM-300 multi-function cold bending machine

Cold bending machine is a kind of hydraulic mechanical processing equipment that bends section steel into different radian radii. The GM-300 series cold bending machine produced by our company is mainly used for bending steel such as steel arch. Through continuous improvement, the series cold bending machine has the advantages of simple operation, high processing efficiency, and sensitive control. It is widely used in tunnel construction, mining roadway construction, and the fabrication and construction of various arches and models for landscape steel structure modeling construction.

1. Main technical parameters

Bending capacity: round tube, I-beam, H-beam, channel steel, square tube and other steel

(1) Overall dimension: length * width * height=4000 * 1800 * 1800mm

(2) Cylinder pushing speed: 2-5mm/s

(3) Minimum bending radius of workpiece: 2500mm (depending on steel specification)

(4) Rated working pressure of hydraulic system: 15MPa (maximum 60mpa)

(5) Drive wheel speed: 3.8 rpm

(6) Linear speed of driving wheel: 3.8m/min

(7) Cylinder stroke: ≥ 200mm

(8) Total power: 19KW Voltage: 380V

(1) Driving wheel motor: 2 * 7.5KW

(2) Oil pump motor: 4KW (high pressure)

(9) Operating weight: 3500Kg

(10) Curve diagram of top wheel stroke and workpiece bending radius of cold bending machine:

Driving wheel radius. r Top wheel travel S

Center distance of driving wheel A Bending outer circle radius R

Curve function of top wheel stroke S and workpiece bending radius R:

S=R+r-√[(R+r) ²- (A/2) ²]

For example: R=1500 r=82.5 A=1790

S=1500+82.5-√[(1500+82.5) ²- (1790/2) ²]=277.4

The ABC curve in the figure is the function curve between the top wheel stroke and the bending radius of the workpiece. The AB section is the normal bending range, and the short BC section is the small radius bending. The forming effect is not good and should not be selected.

二, System introduction

1. Mechanical system

The mechanical system uses a cycloid pinwheel reducer to directly drive the roller to rotate at a speed of 3.7r/min. In order to realize the synchronization of the two rollers, two motors are started at the same time to realize the synchronization. In order to meet the working conditions, forward and reverse transfer can be carried out.

2. Hydraulic system

The system uses a manual reversing valve to reverse the oil pump and realize the forward and reverse movement of the oil cylinder. The one-way throttle valve is used to regulate the movement speed of the oil cylinder, and the two-way hydraulic control one-way valve is used to lock the oil cylinder. When the reversing valve is in the middle position, the system unloads, effectively preventing the system from heating.

3. Electrical system

The electrical system mainly controls the oil pump motor and the traveling roller motor. The traveling motor is equipped with positive and reverse control and overload protection. When the return oil filter is blocked and the filter element needs to be replaced, the indicator light of the filter blockage is on, and the filter element needs to be replaced. An air switch (main switch) is set in the main oil return circuit to effectively protect the whole system.

WxiJiniu Machinery Co.,ltd. formerly known as Wuxi Metallurgical Machinery Factory, registered trademark for "Jinqiu" brand, was founded in June 1969. It is in Wuxi city, 150 kilometers far from Shanghai city. We have been to stated enterprise, since 2002, we recombined to private company, and got fast development, we are one big group now, our group mainly produces hydraulic press brake, hydraulic shears, coiling feeding line--especially for aluimnum cap making, slitting line, cut to length, transformer machines....and other series product. It is one of the earliest factory in China to make these metal sheet machines.

The company covers an area of 62,000 square meters with 300 people. It has advanced production equipment’s with imported large CNC gantry milling machine, imported large CNC boring and milling machine, 100-ton carriageway and a series of iconic devices. Our excellent design team can make personalized products according to the users’ demands. At the same time, we have established long-term cooperation with some famous university, such as Jiangnan university, Nanjing University, Jiangsu University. Through our research staff innovation and hard work, we have received dozens of patents. At the same time, we have ISO and CE certifications.

In the domestic market, we set up many offices in different cities, Beijing, Kunming, Hefei…And to the international market, in many countries, we have sales and service agent, USA, Peru, Brazil, India, Russia…. Our engineers have been to those countries to install our machines. Because of our machine good quality and good after-sales service, the customers give us very high commend.

We hope to set up very good and long cooperation with more customers around the word.