Center Air Suspension Spring For Trailer Flatbed Can Life About 60-70mm Reduce Tire Wear

Center Air Suspension For trailer flatbed Can Life About 60-70MM Reduce tire wear

GUOMAT G-02 Specifications and Detail Technical Parameters

Center suspension G-02
Main customer group: trailer flatbed
1. Customers with very good road conditions, such as dock transfer container flatbed semi-trailers, are transported all day, and the road conditions are relatively good. Half way back and forth is empty cars. When returning, the unused axles can be raised by 5-7CM, saving fuel. To reduce the loss, you can also install two sets of front and rear axles at the same time, which does not affect the normal operation of the empty car. Sometimes a standard axle can be used to lift a rear axle to achieve the required effect.
2. For customers with many corners on the mountain road, many times the front axle is not used, but the tires are rubbed, which affects the tire life and fuel consumption. At this time, installing the center suspension can lift the front axle. Driving on mountain roads and bumps can greatly avoid tire friction , Reduce fuel consumption, according to our customers' long-term feedback on the use of this product, 4-6 months can save four tires on the front axle, fuel consumption than the five months before the conversion saved 2,000 yuan in fuel costs.

Because the installation of this product does not need to modify the original vehicle axle device, it is directly installed, which is not a modification. It can be reviewed regularly and meets national requirements.
The theoretical lift is 60-70MM; if the later installed vehicles need to be lifted higher, three of the ten leaf springs can be removed, and the height can be increased to 10MM

specifications:

1. This picture shows the frame center question [940, ordinary American suspension, axle
1310 models with front axle mechanical suspension lift
2. This lifting device is only for no-load lifting in principle, 1 theoretical lifting
The height is 60 70 mM, if you need to re-educate or raise the height, there are other requirements
Requirements, corresponding changes should be made in the mechanical suspension and spring steel plate
3. Wood lifting device for steel plate problems caused by frequent use of L condition
Not responsible
4. Confirm the center of the axle 61 cm after the front of the pedestal bracket, and
The mounting plate is placed under the center lifting ears, and
The side is closely attached to the frame vertical plate, and the front and rear margins-caused
5. ▲ Special Tips ▲ Perform welding positioning as shown in the figure.
Welding and positioning of the frame stand plate, and lifting ears and positioning plate
For welding positioning, do not weld laterally under the frame
6. After the airbag is fixed and tightened the bolts, please tighten the limit drawing bolts, and
Install the bolt on the lifting beam as shown in the figure, and tighten the release cap
7.0-type bolt 'j axle has about 200 margins to ensure axle upturn
Does not cause crush damage to the lifting device during bumpy road conditions

Guangzhou Guomat Air Spring Co., Ltd. is located in Guangzhou, about 15min’s drive from Baiyun Airport. Our mainly products are air spring, rubber bellows, air suspension spring, air suspension compressor and refitted suspension system. They are widely used in bus, truck, cabin, vehicles’ seat, luxurious car and industrial machine field.

GUOMAT Factory gate：

Established in 2008, Our company covers 20,000㎡ and is located in Taihe Town Baiyun District. With the rapid development of our company, we are equipped with modernized workshop and advanced rubber air springs equipments now. We are the first company who started air spring business and has become one of the largest air spring manufacturing bases in China.

In 2017, we launched a collaboration with High Tech of US customers to customize the products of our customers and the logo of our customers. Every year, there are about 10,000 orders. In continuous cooperation, the products meet the international inspection standard ISO/TS16949:2009, and the customers are very satisfied with the products produced. This is our high recognition from American customers and also gives us Great motivation.

In 2018, we started cooperation with German GmbH, mainly industrial air springs, which are suitable for industrial equipment. We have successfully developed and produced the natural air-seal of the skin to reach the 700mm flanged air spring, the customer's annual demand is a few hundred.

With the development of business and demand for customers, our company introduced business with TomLog Corporation in 2010, our strategic cooperative partner in Taiwan. Then we developed air compressor program and air spring related business, in 2015, America Goodyear Corporation met with the transfer of shares in the North American plant, our company was granted with sale agent for air springs in China, providing more choice for our customers. Our company adopts the most advanced domestic air spring processing equipment and international production technology. Combined with unique production process, our company strictly execute international standards for production and spare no efforts to create the world-class products. We will endeavor to make air spring widely used at home and abroad, and let more and more customers to enjoy the best damping effect.