

Add to Cart
Bored Piles Inspection Deep Drill Hole Monitoring Tester Ultrasonic Bored Pile Foundation Tester
The Drill Hole Monitor system consists of a weighted sensor that is lowered into the While the sensor is lowered or raised to/from the bottom of the shaft, ultrasonic signals are emanated in either two or four directions. The hole geometry is interpreted from measurements of the time it takes for the signals to travel back to the sensor as the signals are reflected off the excavation sides.
These profiles are then plotted and provide a graphical
representation of the verticality and diameter over entire length
of the shaft/pile. In the case of larger deviations from plumb,more
accurate results on verticality and actual diameter can be obtained
by post-processing the data using circle fitting procedures.
digital data are recorded for long-term retention or further
analysis of the results.
Main uses
1. Detection of hole diameter, hole depth, verticality, collapse
expansion and contraction position and tilt direction of bored
piles;
2. Detection of underground continuous wall groove width, depth,
verticality, collapse expansion and contraction position and tilt
direction;
3. Detection of hole expansion effect of branch piles and expanded
bottom piles;
4. Detection of sediment thickness
Specification
Drill Hole Monitor Controller | |||
Display: | 7'' LCD display ,800×600 backlight adjustable | Processor:: | Embedded dual-core processor |
Memory: | 8G TF memory card | Operating system: | Linux operating system |
Control method: | Photoelectric knob | Power: | 12V lithium battery continuous operation for more than 10 hours |
Data interface:: | USB2.0 port | Water/dustproof: | IP67 |
Outlook size | 255mm×192mm×74mm;probe≤6Kg | Weight: | ≤1.8KG |
Depth encoder | |||
Water/dustproof: | IP67 | Power: | Controller supply |
Depth accuracy: | 0.1mm | Weight: | ≤1KG |
Probe | |||
Probe diameter: | Φ24mm,Φ40mm,Φ52mm,Φ65mm,Φ100mm | Detection diameter: | Φ30mm—Φ 600mm |
Waterproof: | Underwater depth up to1000m | Power: | Standard probe host power supply, Deep water probe built-in 12V lithium battery power supply |
Depth: | ≥1000m | controller: | Built-in high-performance microcontroller |
Camera: | 700TV Lines, 0.1Lux, panoramic 360 | Auxiliary light source: | ≥30Lux, adjust the brightness through the host software |
Image pixels: | 1.3 million pixels | Way of Movement: | Horizontal inclined hole mating special guide push rod |
Three-dimensional compass: | Inclination range: ±90 accuracy: 0.5 , resolution: 0.01 ;azimuth range: 0 to 360 ,accuracy: 0.5 , resolution: 0.1 ; probe allows roll 360 | ||
Dimensions | Φ40×613mm Φ24×130mm | Weight | ≤4KG |
Product detailes
Follow the specifications
1. "Technical Specifications for Building Pile Foundations
JGJ94-2008"
2. "Technical Specifications for Highway Bridge and Culvert
Construction JTG/T F50-2011"
3. "Construction Quality Acceptance Specifications for Building
Foundation Engineering GB 50202-2002"
4. "Technical Specifications for Bored and Cast-in-Place Pile Holes
and Underground Continuous Wall Grooving Testing DB/T 29-112-2010
(Tianjin)"
5. "Technical Specifications for Bored and Cast-in-Place Pile Holes
and Underground Continuous Wall Grooving Quality Testing
DGJ32TJ117-2011 (Jiangsu)"
6. "Technical Specifications for Bored and Cast-in-Place Pile Holes
Quality Testing T/CECS 596-2019" China Association for Engineering
Construction Standardization
7. "Technical Specifications for Underground Continuous Wall
Testing T/CECS 597-2019" China Association for Engineering
Construction Standardization