OMCS-30 Central Feeding Systems Drying Mixing Plastic Handling Customized

OMCS Central Feeding System.pdf

Central Drying & Feeding System of Vacuum Central Feeding System

Material Area (Material Silos) of Vacuum Central Feeding System

Utilizing the method of vacuum conveying, Orste Central Material Feeding/Conveying System (OMCS) transports plastic materials from storage silos to the central dehumidifying & drying system through centralized piping, and then convey the dried material to each molding machine. OMCS is suitable for the integrity of the material of huge capacity, eliminates waste and improves the cost effectiveness of the factory.

Product Introduction of Vacuum Central Feeding System

Utilizing the method of vacuum conveying, Orste Central Material Feeding/Conveying System (OMCS) transports plastic materials from storage silos to the central dehumidifying & drying system through centralized piping, and then convey the dried material to each molding machine. OMCS is suitable for the integrity of the material of huge capacity, eliminates waste and improves the cost effectiveness of the factory.

Features of Vacuum Central Feeding System

Continuous auto-operation.

Various dosing & mixing for different colors and materials.

Effective instant recycling which can mix regrind and new material flexibly.

Offer you the most flexibility to easily be expanded or modified equipment, make sure your production safer and more reliable and keep the best working environment.

Components of Vacuum Central Feeding System

OMCS Control Station of Vacuum Central Feeding System

Ideal design of integrating the monitoring panel and the control panel.

Friendly interface and accurate control.

Operating and monitoring by a single personnel and can be linked with a PC.

Conveying time, material types, and pipe cleaning time of each station are adjusted by the control station.

Displaying panel shows you how stations, dryers and storage silos work, such as on/off, full or lack of material, and material types of each station.

Extensive interface allows easy expansions up to 40 stations for future demands.

Compact and durable.

Microprocessor touch-style control panel of Vacuum Central Feeding System

Operating status:

Display the operating status of machines.

Set-up status:

Display the set up status, such as working stations, material types, material conveying time, and pipe cleaning time.

Abnormal:

Display abnormal machines and material type.

“OMCS” Control Unit of Vacuum Central Feeding System

Ideal design of integrating the monitoring panel and control panel, User-friendly interface, Compact & Durable, Small space to make more productive use of factory floor space.

High-pressure Blower of Vacuum Central Feeding System

Pressure air adjustable.

Maximum conveying distance can be 150 meters.

Suitable for conveying the material of large capacity.

Material Selector of Vacuum Central Feeding System

Stainless steel made to avoid pollution of materials. Quick coupling devices for quick set-up or easy disconnected with pipes.

Dust-removing Combination: Vortex Cylone & Pulse Dust Collector of Vacuum Central Feeding System

Collect dust from the conveying system efficiently.

Double protections for high-pressure blower in operation. Easy to maintain: only to change the filter on time and clean conveniently.

Dedicated and compact design.

Material Cut-off Valve: Stainless steel made, durable device design.

Air Cut-off Valve: Stainless steel made, reliable device design.

Compression Couples: Stainless steel made, connect pipes to construct the completely-closed central vacuum conveying system.

Parameters of Vacuum Central Feeding System

Notes:

1. The above parameters is only for reference, the actual parameters is made according to the actual requirement and site condition.

2. Power: 3 Phase / 380 V /50 Hz (Can be customized)

Application Cases of Vacuum Central Feeding System

Central Material Room (Central Control Station, Electric Cabinet, Central Blower, Material Dryer)

PLC Touch Screen (with many screens for different functions) of Central Control Station

Central Piping System (with vacuum air pipe, material pipe, pipe clamps, bends, supporting frames and etc)

Soft pipes for connecting the SUS pipes to the hopper receiver at the feed port of each IMMs (Material cut-off device, Air cut-off device, hopper receivers)

Matters Needing Attention

Electrical installation of the machine should be done by qualified electricians.

Connecting the cooling water (if needed) after the machine is installed in a appointing place, make sure the inlet and outlet water pipe is in good condition.

Before connecting to AC Power Source, turn power switch to OFF position. While AC power source is connected, make sure specifications and overload protection rating of the power switch are suitable and reliable. When the machine is under care or maintenance, turn off both power switch and automatic operation switch.

Dongguan Orste Machinery Equipment Co., Ltd. was established in 2007 in “Made in China” City, Dongguan, Guangdong Province. After many years of growth and development, Orste has become a technology driven and innovative enterprise with independent development ability, integrating design, manufacturing, sales and maintenance.

We have been awarded ISO9001 certification. Orste now owns 1 manufacturing factory in Dongguan and 12 sales agent service centers in many cities in China including Tianjin, Jinan, Suzhou, Shanghai, Wenzhou, Fuzhou, Wuhan, Changsha, Chongqing and etc. With a foothold set in China, we are serving global markets. Orste devotes itself to improving the product quality and working environment in plastic factories by supplying integral automation systems to them.

With many years of experience and accumulation in Dehumidifying and Drying, Material Conveying, Heating and Cooling, Granulating and Recycling, Mixing and Blending, and upholding the principle of “Focusing on Product Details, Pursuing Excellent Quality”, Orste Machinery is an industry leader with its mature technology in peripheral equipment of plastic molding.

Orste’s large scale central material feeding system and cooling water circulation system including three major systems of centralized raw material drying, water temperature control and metering & mixing, are extensively applied in plastic injection molding industry. The main products of the company are a series of high-tech products including Dehumidifying Dryer, Hopper Dryer, Auto-loader, “Three-in-one” Compact Dryers, Water/ Oil Mold Temperature Controller, Industrial Cooling Machine, Granulator, Mixer, Masterbatch Doser and Vibrating Screen.

With the principle of customer satisfaction first, we take value contribution as our responsibility and constantly review the market adaptability of our products to timely seize the latest trend in industry, and maintain the uniqueness and technological edge of products. Through proactive listening, delicate service, modest attitude, Orste Machinery always maintains close contact with its customers.