45mA Portable Handheld Potentiostat Galvanostat CS100E With EIS

45mA Portable Handheld Potentiostat Galvanostat CS100E With EIS

The CS100E handheld potentiostat supports full electrochemical methods, including potentiostatic/galvanostatic polarization curve, Cyclic voltammetry analysis, impedance(EIS), and galvanic current measurement. etc. It has built-in chargeable li-ion battery and Bluetooth communication. The device supports laptop/computer software or mobile APP. It can be used for electrochemical tests in field or special non-electricity environment. CS100E can be a convenient handheld tool for researchers of energy& materials, environment protection, biosensor, foods &drugs, corrosion protection etc. Maximum current is ±45mA

The voltage control range is ±10V, compliance voltage is ±12V, the maximum current output is ±45mA, and the minimum current resolution can reach 100fA. The EIS frequency range is 10μHz~1MHz.

Thanks to its small size with comprehensive electrochemical functions, it’s typically used for:

- Battery materials’ performance test in a glove box

- Ultra-low detection limit of heavy metal ions for water quality test in environmental protection field

- Low current detection in biosensor thanks to high current accuracy

- Effective ingredients detection in food and drug industry

- Outdoor bridge corrosion and soil corrosion measurements

Note: maximum current during experiment doesn’t exceed ±45mA then the handheld potentiostat can be used. If exceeds ±45mA an ordinary size potentiostat with maximum current ±2A should be considered.

Features

- Small & light, handheld and convenient

- Easy to install and use

- High accuracy, current resolution can reach to 100fA, and measurement accuracy is 0.1% of the range.

-during outdoor test, a laptop’s USB port can be used for both charging and communicating

- The circuit adopts floating design. Electrochemical parameters of the grounded system can be measured without an isolation transformer.

Specifications of the portable potentiostat

Size / weight:15 x 9 x 3 (cm), 450g

Potential control range: ±10V

Maximum current: ± 45mA

Compliance voltage: ±12V

EIS frequency range: 10μHz ~ 1MHz(CS100E)

Potential range: ±2.5V, ±5V, ±10V

Current range: 200pA~50mA, 9 ranges

Potential accuracy: 0.1%× full range

Minimum potential resolution: 10mV

Current accuracy: 0.1%× full range

Minimum current resolution: 100fA

Reference electrode input impedance: 10¹³Ω||8pF

AC amplitude: 0~±2.5V

Signal response bandwidth: 1MHz

Max. acquisition rate: 150,000 data points/s

CV and LSV scan rate: 0.001mV~ 10V/s

Support 2-, 3-or 4-electrode system

Communication: USB / Bluetooth

Power supply: USB / built-in li-ion battery 6000mAH@3.7V

Electrochemical techniques- handheld potentiostat CS100E

Stable polarization

• Open Circuit Potential (OCP)
• Potentiostatic (I-T curve)
• Galvanostatic
• Potentiodynamic (Tafel plot)
• Galvanodynamic (DGP)

Transient Polarization

• Multi Potential Steps
• Multi Current Steps
• Potential Stair-Step (VSTEP)
• Galvanic Stair-Step (ISTEP)

Chrono Method

• Chronopotentiometry (CP)
• Chronoamperametry (CA)
• Chronocaulometry (CC)

Voltammetry

• Linear Sweep Voltammetry (LSV)
• Cylic Voltammetry (CV)
• Staircase Voltammetry (SCV) #
• Square Wave Voltammetry (SWV) #
• Differential Pulse Voltammetry (DPV) #
• Normal Pulse Voltammetry (NPV)#
• Differential Normal Pulse Voltammetry (DNPV) #
• AC Voltammetry (ACV)
• 2^nd harmonic AC Voltammetry (SHACV)
• Fourier Transform AC Voltammetry (FTACV)

# there is correspinding Stripping Voltammetry

Electrochemical Impedance Spectroscopy (EIS)

• Potentiostatic EIS (Nyquist, Bode)
• Galvanostatic EIS
• Potentiostatic EIS (Optional freq.)
• Galvanostatic EIS(Optional freq.)
• Mott-Schottky
• Potentiostatic EIS vs. Time (Single freq.)
• Galvanostatic EIS vs. Time (Single freq.)

Corrosion Measurements

• Potentiodynamic (Tafel plot)
• Cyclic polarization curve (CPP)
• Linear polarization curve (LPR)
• Electrochemical Potentiokinetic Reactivation (EPR)
• Electrochemical Noise (EN)
• Zero resistance Ammeter (ZRA)

Battery test

• Battery Charge and Discharge
• Galvanostatic Charge and Discharge (GCD)
• Potentiostatic Charging and Discharging(PCD)
• Potentiostatic Intermittent Titration Technique(PITT)
• Galvanostatic Intermittent Titration Technique(GITT)

CorrTest Instruments Co. (China) manufactured her first full-digital potentiostat/galvanostat for corrosion electrochemistry in 1995. After 29 years of research and development, CorrTest has developed a series of electrochemical workstations dedicated to electroanalysis, corrosion, electrocatalysis, energy material research, sensors, electrodeposition etc. CorrTest has registered CorrTest^® trademark and acquired a number of patents, software copyrights.

CorrTest has also developed different kinds of corrosion sensors and meters, corrosion management networks for on-site corrosion monitoring and risk evaluation of oilfields, petrochemicals, construction and offshore wind farms.

“Quality from Technology", "Progess from Profession" is our motto for research and development. CorrTest will continue to provide customers with high-quality products and professional services.

1995：1^st electrochemical potentiostat was made based on AD&DA multifunction board

2007：CorrTest was officially established with 1^st generation CS350 potentiostat designed

2015：2^nd generation CS350G potentiostat with the achievement of 1MHz impedance

2016：Listed on China’s New OTC market and embarked on 1^st generation corrosion meters

2017：3^rd generation CS350H potentiostat, specializing in EIS for high-impedance coating

2021：4^th generation, CS350M and CS310X multichannel products

2023：5^th generation, CS2020B high-power booster to enhance CS350M output current