B&R ID code

0x12C8

Slots for plug-in modules

4

Certifications

CE

Yes

UKCA

Yes

Functional safety

Yes

UL

cULus E225616
Power conversion equipment

KC

Yes

Permissible network configurations

TT, TN

Mains input voltage

3x 400 VAC to 480 VAC ±10%
3x 230 VAC ±10%

Frequency

50 / 60 Hz ±4%

Installed load

Max. 10 kVA

Inrush current at 400 VAC

7 A

Switch-on interval

>10 s

Integrated line filter per EN 61800-3, category C3

Yes

Power dissipation at device nominal power without braking resistor

Approx. 200 W

DC bus capacitance

470 µF

Input voltage

24 VDC ±25%

Input capacitance

8200 µF

Current consumption

Max. 2.5 A + Current for motor holding brake

Quantity

1

Continuous current

8.8 Aeff

Reduction of continuous current depending on ambient temperature

Mains input voltage: 400 VAC

Switching frequency 5 kHz

No reduction

Switching frequency 10 kHz

0.18 Aeff per °C (starting at 54°C)

Switching frequency 20 kHz

0.18 Aeff per °C (starting at 30°C)

Mains input voltage: 480 VAC

Switching frequency 5 kHz

No reduction

Switching frequency 10 kHz

0.18 Aeff per °C (starting at 48°C)

Switching frequency 20 kHz

0.18 Aeff per °C (starting at 18°C)

Reduction of continuous current depending on installation elevation

Starting at 500 m above sea level

0.88 Aeff per 1000 m

Peak current

24 Aeff

Nominal switching frequency

10 kHz

Possible switching frequencies

5 / 10 / 20 kHz

Insulation stress of the connected motor per IEC TS 60034-25:2004

Limit value curve A

Max. motor line length

25 m

Protective measures

Overload protection

Yes

Short-circuit and ground fault protection

Yes

Max. output frequency

598 Hz

Terminal connection cross section

Flexible and fine-stranded wires

With wire end sleeves

0.25 to 4 mm²

Approbation data

UL/C-UL-US

30 to 10 AWG

CSA

28 to 10 AWG

Response threshold for open-circuit monitoring

Approx. 385 mA

Max. output current

1 A

Max. number of switching cycles

Unlimited since implemented electronically

Peak power output

7 kW

Continuous power

200 W

Quantity

3

Circuit

Sink

Electrical isolation

Input - ACOPOS

Yes

Input - Input

No

Input voltage

Nominal

24 VDC

Maximum

30 VDC

Switching threshold

Low

<5 V

High

>15 V

Input current at nominal voltage

Approx. 4 mA

Switching delay

Max. 2.0 ms

Modulation compared to ground potential

Max. ±38 V

Quantity

1

Circuit

Sink

Electrical isolation

Input - ACOPOS

Yes

Input voltage

Nominal

24 VDC

Maximum

30 VDC

Input current at nominal voltage

Approx. 30 mA

Switching threshold

Low

<5 V

High

>15 V

Switching delay

Enable 0 → 1, ready for PWM

Max. 100 µs

Enable 1 → 0, PWM off

Max. 2.0 ms

Modulation compared to ground potential

Max. ±38 V

OSSD signal connections

Not permitted

Quantity

2

Circuit

Sink

Electrical isolation

Input - ACOPOS

Yes

Input - Input

No

Input voltage

Nominal

24 VDC

Maximum

30 VDC

Switching threshold

Low

<5 V

High

>15 V

Input current at nominal voltage

Approx. 10 mA

Switching delay

Rising edge

52 µs ±0.5 µs (digitally filtered)

Falling edge

53 µs ±0.5 µs (digitally filtered)

Modulation compared to ground potential

Max. ±38 V

Discharge capacitance

660 nF

Energy efficiency (IE classification)

Power dissipation relative to continuous apparent power

IE2 (10,25) 1.6%
IE2 (50,25) 1.6%
IE2 (10,50) 1.8%
IE2 (50,50) 1.9%
IE2 (90,50) 2%
IE2 (10,100) 2.2%
IE2 (50,100) 2.5%
IE2 (90,100) 2.9%

Nominal losses in standby mode

16.8 W

Permissible mounting orientations

Hanging vertically

Yes

Horizontal, face up

Yes

Standing horizontally

No

Installation elevation above sea level

Nominal

0 to 500 m

Maximum

2000 m

Pollution degree per EN 61800-5-1

2 (non-conductive pollution)

Overvoltage category per EN 61800-5-1

II

Degree of protection per EN 60529

IP20

Temperature

Operation

Nominal

5 to 40°C

Maximum

55°C

Storage

-25 to 55°C

Transport

-25 to 70°C

Relative humidity

Operation

5 to 85%

Storage

5 to 95%

Transport

Max. 95% at 40°C

Dimensions

Width

70.5 mm

Height

375 mm

Depth

235.5 mm

Weight

4.4 kg