M8 - M18 Electric Pipe Threading Machine Stainless Steel Pipe Threader 1/2″-2″
Brand Name:HXTG
Certification:ISO9001
Model Number:ZT-M18
Minimum Order Quantity:1set
Delivery Time:20days
Payment Terms:D/P, T/T
Contact Now
Add to Cart
Active Member
Location:
Hangzhou China
Address:
No. 58, Leiting Rd., Hangzhou, China.
Supplier`s last login times:
within 36 hours
Product Details
Company Profile
Product Details
Electric Pipe Threading Machine stainless steel pipe threader Size: 1/2″-2″ ZT-M18
Introduction
ZT-M18 universal manual die head pipe threading machine is the best performance for galvanized, mild steel, stainless steel pipe threading outer dia widely used in industries, firefighting, Factories, Plumbing Contractors, water pipeline contracts, sewerage, and irrigation work.
Model no. ZT-M18, Application – MS & GI Pipe, Motor: 750w induction type which enables the machining process standard threads, Speed: 46 RPM, Manual Die head (1/2″-2″): manual type, Compact design with cast aluminum body. Easy and fast transport and set-up, Chuck: Hammer-type with replaceable, rocker-action jaw inserts, Rear centering device: Cam-action, Oiling system: through the head, with an integral oil reservoir, self-priming, constant-flow, Standard alloy dies, Packing – Wooden Crate Packing, Dimension: 70*48*54cm, Weight: 68/56Kg, Universal applicable can also work on the workbench.
Keywords : pipe threading machine, electric pipe threading machine, Iron pipe threading machine, steel pipe threader, stainless steel threading machine, portable pipe threading machine, electric manual pipe threading machine
Technical data
| Product Name | Electric Pipe Threading Machine stainless steel pipe threader Size: 1/2″-2″ ZT-M18 |
| Rotational speed of main shaft | 46 r/min |
| Model of die head | Die head for Bolt (1/2″-2″) |
| Scope of application | 1/2-2" |
| Power of motor: | 750w |
| Gross net weight | 68/56kg |
| Packing dimension | 700mm*480mm*540mm |
| Item | electric ratchet pipe threader |
| Key word | rod threading machine |
Detail photos
How to Threading
(1) Pull the cutting knife frame and chamferer; put down die head to touch the copying block. After reliable positioning of die head, press the button to start the machine.
(2) Rotate the pipe in anti-clockwise direction, rotate the hand wheel of cutting feed, and make die head get close to the pipe.
(3) Apply force to the hand wheel of cutting feed, until die head makes 3 ~4 threads on the pipe.
(4) Then, loosen the hand wheel of cutting feed, so the machine starts automatic threading. When roller of die head goes over copying block and falls down, threading die will open automatically and the threading is completed (Z13 T–M18 threading machine is required to turn back to make the threading die exit). Z1T–50A threading die shall be loosened manually.
(5) Machine halt. Return to the carriage, until the whole die head exits pipe end. Pull out die head, lock the handle and pull up the die head.
Important Notice
1. This machine shall be used with reliable grounding and anti-creep device.
2. Children are prohibited from touching this machine to avoid injury.
3. This machine shall not use the same socket with large-power machines, such as electric welding machine.
4. Pipe clamps shall not be installed on the machine, to avoid cracking of main components such as the cabinet.
5. Saponified solution shall not be used for cooling, such as water.
6. When above 2½″ pipe thread is made, it is required to adopt the low-gear processing mode,
7. When leaving factory, centrality of the machine has been measured, but pipes on the market have certain ovality at present. After machining, screw threads may be deep on one side and shallow on the other side. If they affect use, please check the quality of pipes.
Common Faults and Solutions
Common faults | Reasons | Solutions |
|---|---|---|
| 1. Motor doesn’t work or work with intermittent sound | 1. Fuse is burnt down 2. The plug is not well connected 3. The internal part of the cable is broken 4. The button switch is not well connected 5. 100UF Capacitor breakdown 6. Environment temperature is too low, and lubricating grease solidifies. | 1. Detect the broken part with a multimeter and use a new fuse 2. Replace the plug or socket 3. Replace the power cord 4. Replace the switch 5. Use a new capacitor 6. Operate indoor or help it to start up |
| 2. Pipe fails to be fixed and slips during threading | 1. Insufficient hammering force 2. Clamping jaw tip turns over 3. One clamping jaw tip breaks or has a gap | 1. Hammer hard 2. Adjust clamping jaw tip 3. Use a new clamping jaw tip |
| 3. Cutting knife fails to cut, and fails to produce proper threads | 1. Sharp corner of cutting knife is worn out and becomes an arc 2. Pin roll of cutting knife is worn out 3. Cutting force is insufficient | 1. Replace cutting knife blade 2. Replace pin roll 3. Cut more vigorously |
| 4. Knife cannot cut during threading | 1. Opening of threading die is too small at the start of threading 2. Several teeth of knife head are broken 3. Knife head doesn’t match 4. There is scrap iron in die groove | 1. Use threading die correctly 2. Replace knife 3. Re-install knife head 4. Clean threading die head |
| 5. Front chuck loosens and falls down | Screws loosen due to long-term use | Inspect them timely |
| 6. Main shaft is heated and jammed | Insufficient oil | 1. Add oil timely 2. Exit beam barrel and repair shaft sleeve |
| 7. Cooling oil doesn’t come up | 1. Oil line is jammed 2. Oil hole doesn’t align after dismantling and re-assembling fulcrum shaft of die head. 3. Oil leaks from oil pump after stopping use for a long time 4. Oil pump is worn out 5. Rotor pin roll of oil pump is broken | 1. Clean oil line 2. Re-assemble 3. Add some cooling oil into oil pump 4. Replace oil pump |
| 8. Oil leakage | 1. Oil line plugging leads to falloff or rupture of oil line. 2. Oil draining screw in the oil tank isn’t tightened | 1. Inspect plugging point and replace oil line 2. Tighten oil draining screw |
| 9. Cooling oil leaks into motor | Skeleton type oil seal of oil pump PD8×22×8 is damaged | Replace a new oil seal or oil pump |
| 10. Three-phase motor is burnt down | Phase loss or bad contact | Carry out the winding and check the circuit |
| 11. Single-phase motor is burnt down | 1. Starting voltage is too low 2. Environment temperature is too low, and lubricating grease solidifies. | 1. Wind wires and inspect voltage; replace qualified power line and power supply 2. Wind wires and carry out indoor operation |
| 12. Unilateral threads | 1. Oval pipe 2. Clamping jaw tip breaks or has a gap | 1. Replace the pipe 2. Replace the clamping jaw tip |
FAQ
1. How to get a accurate quotation from us?
Provide us the detail of the material such as metal thickness and
width.
2. What’s the shipping cost from China to your country?
We can send machine to your port or door address by sea or
airplane. Please kindly tell us your nearest port or address with
postcode.We have reliable shipping agent to insure the safe,
convenient and timely delivery.
3. Payment terms, MOQ, warranty, FOB?
Payment terms: 30% TT paid in advance, the balance of 70% before
the shipment.
Minimum order quantity: 1 set.
FOB :Shanghai/Ningbo
Delivery time :7 days after receipt of formal order and 30%
deposit.
Warranty:12 months.
4. What’s the package?
Fumigation-free plywood case.
5. What about commissioning service?
We can offer commissioning service, the buyer need to afford plane
tickets.
6. What’s policy for guarantee and broken parts?
Warranty period of equipment lasts a year, during which the broken
parts and spares caused by quality can be offered free.
7.Any question, call us or send email, we will try our best to
satisfy you.
M8 - M18 Electric Pipe Threading Machine Stainless Steel Pipe Threader 1/2″-2″
Inquiry Cart
0