Product Details
Disposable Virus Sampling Tube
Structure Composition
The product consists of swab and tube containing preservation
solution. Non sterile. The material of sampling tube body is PP,
the material of cap is PE, the material of swab rod is ABS, and the
material of swab head is nylon
Sampling Tube
- The sampling tube body is transparent, the surface is smooth, and
the label is clear and complete.
- The pipe body has no stain, obvious scratch, crack, even thickness
of pipe wall, no obvious bending and deformation; The cap fits well
with the pipe body and rotates tightly without skew cover
Preservation Solution
- Liquids should be odorless, tasteless, without visible particles or
impurities. No turbidity may occur. Foam or bubbles are normal
phenomena during transportation and use.
- The standard range of pH value is 7.0-8.5
- The storage capacity
is:1ml,1.5ml,2ml,2.5ml,3ml,3.5ml,4ml,5ml,6ml,7ml,8ml,9ml,10ml,12ml,15ml,20ml,25ml,
Tolerance ±10%
Sampling Swab
- The sampling swab should be clean, odorless and tasteless. The head
of the sampling hair should be soft and the surface should be free
of macula, impurities and hair loss
- When the moving speed of the fixture of the tester is 200 mm / min,
the pull-out force between the head of the sampling swab and one
end of the connecting rod shall not be less than 2 n
- When the test span is 6cm (the span range should avoid the breaking
point), the plastic rod should be able to withstand 5N axial static
pressure for 15s without permanent deformation or breaking
- Fixed sampling swab head, 90 ° Under vertical downward pressure,
the breaking force at the breaking point of the sampling swab
should not be less than 2n.
- After the tube body with preservation solution is matched with the
cap, the tube body and cap will not break, and the preservation
solution shall not leak.
- The product identification shall be clear, intact, clean and
undamaged
Swab size Unit: mm
Swab length (L2) | Length of broken head (L1) | Maximum diameter of swab rod (D1) | Minimum diameter of swab rod (D2) | Length of swab head (L3) |
150±5 | Mouth swab | Throat swab | Nasal swab | Mouth swab | Throat swab | Nasal swab | Mouth swab | Throat swab | Nasal swab | 20±3 |
30±5 | 80±5 | 80±5 | 2.5±0.2 | 2.5±0.2 | 2.5±0.2 | 2.0±0.2 | 2.0±0.2 | 1.1±0.2 |
Intended Use
It is suitable for collection, preservation and transportation of
samples from nasal cavity and oropharynx
Applicable Departments
Fever clinic, emergency department, laboratory, infection control
department
Usage Method
- Before sampling, clean hands, tear open the outer package of the
swab, take out the swab, and pay attention not to touch the swab
head.
- According to different sampling requirements, swabs were used to
collect samples from corresponding parts.
- After sampling, quickly put the swab into the collection tube with
preservation solution to avoid contacting other parts.
- Break the swab rod, discard the tail, and then tighten the tube
cover to complete sampling.
- The sampled virus samples should be placed and stored by the
Management Commission, and transported to the testing department
for testing within one week.
Matters Needing Attention
- Confirm that the outer package of the product is in good condition,
check the preservation tube, and confirm that there is no leakage.
- This product is for one-time use, no second use.
- The process of sample collection should be considered as a
potential risk of infection, and the operation and treatment should
meet the requirements of relevant laws and regulations.
- After use, the product should be disposed according to the relevant
regulations of medical waste.
Important
- Make sure that the top of the sampling swab does not touch any
surface before sampling.
- Choking risk, sampling swabs inserted into the mouth should be
careful.
- After the collection of pathogenic bacteria, the disposable swab
should be completely inserted into the preservation solution to
maximize the retention of pathogenic bacteria.
- After use, the tubes and swabs should be disposed of according to
the relevant medical waste treatment methods
Company profile
Zhongxiu Science And Technology Co.,Ltd., is a high-tech enterprise
engaged in the research and development, production and operation
of in vitro diagnostic products. The in vitro diagnostic products
developed by the company cover POCT series, microbial series,
biochemical series and immune series reagents and supporting
instruments.
The company has always adhered to the core concept of "fast and
accurate, living up to life", committed to providing society with
excellent products and services, and contributing to the cause of
human health.
Company Profile
Zhongxiu Science And Technology Co.,Ltd., founded in 2016, is
located in Dingluan Industrial Zone, Changyuan City, Henan
Province. The company covers an area of about 100 acres and the
initial investment is about 200 million yuan. The company has a
scientific and complete management system, a purification workshop
of national standards, and a fully functional inspection center. On
this basis, the company will continue to invest in research and
development, accumulate technical strength, update manufacturing
equipment, improve production technology, improve inspection
technology, improve product quality, and provide customers with
safe and effective in vitro diagnostic products.
Zhongxiu Science And Technology Co., Ltd. is a high-tech enterprise
engaged in the research and development, production and operation
of in vitro diagnostic products. The in vitro diagnostic products
developed by the company cover POCT series, immune series,
microbial series and other reagents and supporting instruments.
The company has always adhered to the core concept of “fast and
accurate, living up to life”, committed to providing society with
excellent products and services, and contributing to the cause of
human health.