10Gbps CWDM SFP+ Cisco Compatible Transceiver 1610nm 10km DOM

10Gbps CWDM SFP+ Cisco Compatible Transceiver 1610nm 10km DOM

Cisco CWDM-SFP10G Compatible 10G CWDM SFP+ 1270~1610nm 10km Transceiver

Product Features

● Supports 9.95 to 11.5Gb/s bit rates

● Duplex LC connector

● Hot pluggable SFP+ footprint

● Uncooled 1270nm~1610nm DFB transmitter, PIN photo-detector

● Applicable for 10km SMF connection

● Low power consumption, < 1W

● Digital Diagnostic Monitor Interface

● Optical interface compliant to IEEE 802.3ae 10GBASE-LR

● Electrical interface compliant to SFF-8431

● Operating case temperature:

Commerical:0 to 70 °C Industrial:-40 to 85 °C

Applications

● 10GBASE-LR/LW at 10.3125Gbps

● 10G Ethernet

● Other optical links

Product Descriptions

Olinkcom’s OLSCxx1XL-C(I)D10 CWDM DFB 10Gbps SFP+ transceiver is designed to transmit and receive optical data over single mode optical fiber for link length 10km. This transceiver consists of two sections: The transmitter section incorporates a CWDM DFB laser. And the receiver section consists of a PIN photodiode integrated with a TIA. All modules satisfy class I laser safety requirements. Digital diagnostics functions are available via a 2-wire serial interface, as specified in SFF-8472, which allows real-time access to device operating parameters such as transceiver temperature, laser bias current, transmitted optical power, received optical power and transceiver supply voltage.

Absolute Maximum Ratings

Note: Stress in excess of the maximum absolute ratings can cause permanent damage to the transceiver.

General Operating Characteristics

Electrical Characteristics (TOP(C) = 0 to 70 ℃, TOP(I) =-40 to 85 ℃,VCC = 3.13 to 3.47 V)

Notes:

1. Connected directly to TX data input pins. AC coupling from pins into laser driver IC.

2. Into 100Ω differential termination.

3. 20 – 80%. Measured with Module Compliance Test Board and OMA test pattern. Use of four 1’s and four 0’s sequence in the PRBS 9 is an acceptable alternative.

4. LOS is an open collector output. Should be pulled up with 4.7kΩ – 10kΩ on the host board. Normal operation is logic 0; loss of signal is logic 1.

Optical Characteristics (TOP(C) = 0 to 70 ℃, TOP(I) =-40 to 85 ℃,VCC = 3.13 to 3.47 V)

Notes:

1.The wavelength λ =1270nm~1610nm, Total 18 wavelengths,20nm spacing

2. Measured at 10.3125b/s with PRBS 2^{31 – 1} NRZ test pattern.

3.Under the ER worst =5, measured at 10.3125 Gb/s with PRBS 2^{31 - 1} NRZ test pattern for BER < 1x10^-12

Digital Diagnostic Specifications

The OLSCxx1XL-CD10 transceivers can be used in host systems that require either internally or externally calibrated digital diagnostics.

Notes:

1.When Operating temp.=0~70 ºC,the range will be min=-5,Max=+75

2. Internally measured

3. The accuracy of the Tx bias current is 10% of the actual current from the laser driver to the laser

Compatibility

Shenzhen Olinkcom Technology Co.,Ltd established in the year of 2011, is a professional manufacturer of optical transceivers. We are dedicated to designing, developing, production and distributing optical transceivers to fulfill customer’s requirements for optical communication. Olink is able to offer a vast range of optical modules from 155Mbps ~ 100Gbps, including CFP2, QSFP+, XFP, SFP+, SFP, PON and CWDM, DWDM solutions, to support various protocols and meet with different requirements on Fiber Channel, Ethernet, SONET/SDH, FTTx, Data Center etc. And all product quality is backed by our strong R&D ability, rigorous quality control procedure and rich production experience. Our modules are exported to China domestic market, Asia, Southeast Asia, Europe and the American market, etc.

With the concept of “Quality First, Service Oriented, Realistic and Innovative, Continuous Improvement”, Olink keeps developing and optimizing product design solutions, to provide our valued customers with the most cost efficient product and service, as well as some customized products.