70 Shore A Good Flowability Low Shrinkage Polyurethane Liquid Plastic For Shoe Sole

Good Flowability Linear Shrinkage Durable RTV-2 Polyurethane Liquid Plastic Resin For Making Shoe Sole Molds

Product Description

Polyurethane liquid rubber consists of A&B component, B is curing agent, and A is polyurethane prepolymer.

can be used as a concrete or cement stamping mold as well as for making hard durable rubber parts for machinery or automotive applications.

Applications

Substitute for making the mould of “cultural stone” and concrete stamping. It also applies to electrical equipment potting, rubber rollers, Ski and snowboard ,rubber plates, rubber wheels, shoe models and others.

Main Features: Polyurethane Resin
Cure at room temperature with the appropriate catalyst
High fluidity (pouring application)
Very little linear shrinkage (no linear shrinkage if charged)
Extreme faithfulness in the reproduction of details from any original model
Excellent surface finish
High crash and scraping resistance
High temperature resistance
Waterproof properties
Excellent dielectric properties
Easy mould building, no need of particular equipments
Adding appropriate charges it is possible to give to the resin special properties

Technical Datasheet

Mixing:
Shake both A and B sides vigorously.
Measure out equal parts, by volume, of A and B into clean plastic or metal containers.
Combine both sides into a third clean mixing container and mix vigorously for at least one minute, taking care to scrape the sides and bottom of the mixing container with your mixing utensil, until the product is one uniform color.

Tips:
Always wear a respirator or self –contained breathing apparatus when working with urethanes.
Use between 65F and 75F in a humidity-controlled environment.
AeroMarine Products Concrete Molding and Stamping Rubber 75A Urethane is moisture sensitive.
Use only clean plastic and/or metal mixing utensils and containers.
Do not use paper or wood.
Re-cap the bottles immediately after use.
Extend-It aerosol nitrogen blanket can be used to protect the product from moisture contamination.
Never mix less than about 3 ounces of product, as this ratio is hard to measure and will take longer to cure as the exothermic reaction does not generate much heat at this volume.
Avoid mixing with drill motors because of the friction they generate, mixing with electric drills can start the exothermic cure process and cause the product to cure in the mixing container.
It is always best to mix the material by hand, with a plastic or metal mixing utensil.
Don’t vary the mix ratio. Unlike some polyester resins, altering the mix ratio to vary the cure cycle will not work with urethanes.
Mix in clean plastic containers. Paper cups and wooden mixing utensils may contain moisture which can adversely affect the urethane rubber. Avoid waxed paper cups because the wax may melt and contaminate the rubber.
Air bubbles in urethanes are almost always caused by moisture. Do everything possible to avoid moisture getting into the mix. Replace the lids onto the containers promptly after use. Do not use the urethane rubber during rainy days or times of high humidity. Avoid pouring against an unsealed water based product such as plaster or hydrocal. Seal plaster or hydrocal with a product like Krylon Clear Acrylic.
Avoid mixing a large batch- The larger the batch, the more exotherm or heat is generated in the cure cycle. If you are making a large mold, mix small batches to make the process more manageable.
Shake or stir well before use- The liquid components may settle in the containers during storage. Shake or stir the components separately and thoroughly before mixing. Let it sit a few minutes to let any bubbles rise to the surface after shaking the container.

Package:20Kg/drum

Storage:Store in cool and dry place. If you can’t use one drum up at a time, please inject N₂.The storage time of original packing is 6 months.

Mingcheng Group Limited was established in 2010 based in Dongguan,China, with brand MC Silicone for overseas market, dedicated to manufacturing and R&D of mold making and casting materials.

Our professional approach to all our work, together with creative ideas and strong technical skills, enable us to produce high quality, cost effective materials. We pride ourselves on the different types of mould making materials we offer.

Why Choose Us?

Our Advantages
More than 20 years experience in moldmaking & casting industry
10 years exporting experience

Benefits of MC Silicone
1- A Technology Team: R&D Support
2- A Factory: customize for you in every possible aspect
3- A Sales Team: assist you develop more markets
4- Fast Delivery time about 3-5 working days per order
5- Professional Sales Service, 12-24 hours response
6- Various Payment Method

If you're looking for a good silicone supplier, you've come to the right place. Our unique vision and mission drives us bring the best products and service to each of our clients. We gonna be your guide in silicone industry, we are your partner. Welcome to Join us.