200mA 250V Electromagetic Field Tester With Self Recovery Fuse

Self-Recovery Fuse 200mA / 250V Electromagetic Field Tester

Security Information

Use this instrument with special attention, improper use may cause electric shock or damage to the instrument. In accordance with the usual safety procedures and full compliance with the safety regulations specified in the manual.
In order to make full use of the functions of the instrument and to ensure safe operation, please carefully read and follow the instructions of this manual.

Instrument in line with GB / T 13978-92 digital multimeter general technical conditions, in line with GB4793.1-1995 (IEC-61010-1, IEC-61010-2-032) electronic measuring instruments safety requirements, is a secondary pollution, For CAT IV 600V and CAT III 1000V.
Follow the safe operating instructions to ensure safe use of the instrument.
Appropriate use and protection, the instrument will give you a satisfactory service.

Technical indicators

Ambient temperature: 23 ± 5 ℃ Relative humidity: <75%
3.2.1 True rms zero input
3.2.1.1 The measurement of sine wave signal, the use of true RMS measurement method than the traditional average response method error is small.
3.2.1.2 True RMS The instrument can accurately measure the sine wave signal, but if it is on the AC function, the instrument may display 1 to 50 if the measured signal is not input (shorted at the AC voltage range and the input terminal) Word between a reading. These deviations are normal. Within the specified measuring range, they do not affect the accuracy of the multimeter to measure alternating current.
3.2.1.3 True RMS requires that the input signal reach a certain level for measurement. Therefore, the AC voltage and current range is specified between 2% and 100% of full scale.



3.2.2 DC voltage

- Input impedance: 10MΩ
- Maximum input voltage: 600V DC or 600V AC (rms)
Note:
In the small voltage range, the pen is not connected to the circuit under test, the instrument may have beating the reading,
This is normal, this is because the instrument caused by high sensitivity, does not affect the actual measurement results.


3.2.3 AC voltage

- Input impedance: 10MΩ

- Maximum input voltage: 600V AC (RMS) or 600V DC

- Frequency range: 40 ~ 1000Hz True RMS

Note:
In the small voltage range, the pen is not connected to the circuit under test, the instrument may have beating the reading,
This is normal, this is because the instrument caused by high sensitivity, does not affect the actual measurement results.



3.2.4 Alternating current

- Overload protection: mA range fuse (self-recovery fuse 200mA / 250V)
10A range without insurance
- Maximum input current: mA: 600mA DC or AC rms;
10A: 10A DC or AC rms;
When the measured current is greater than 5A, the continuous measurement time is not longer than 15 seconds, after the measurement to stop the current measurement for more than 1 minute.
- Frequency response: 40Hz ~ 1000Hz True RMS.

3.2.5 DC

- Overload protection: mA range fuse (self-recovery fuse 200mA / 250V)
10A range without insurance
- Maximum input current: mA: 600mA DC or AC rms;
10A: 10A DC or AC rms;
When the measured current is greater than 5A, the continuous measurement time is not longer than 15 seconds, after the measurement to stop the current measurement for more than 1 minute.


3.2.6 Frequency

- Overload protection: 250V DC or AC (rms)
- Input voltage range: 600mV ~ 10V AC (with the measured frequency increases, the input voltage should also increase)


3.2.7 Duty cycle

- Frequency response: 10 ~ 10MHz

- Input voltage range: 600mV ~ 10VAC (with the measured frequency increases, the input voltage should also increase)

- Maximum input voltage: 250V AC (rms)

Resistance

- Open circuit voltage: approx. 1.0V
- Overload protection: 250V DC or AC (rms)

Transistor test

Capacitance

- Overload protection: 250V DC or AC (rms)

Temperature test

- Overload protection: 250V DC or AC (rms)

Shenzhen Xishen Development Co.,LTD,business mogel for testing instruments for more than 10 years.Our engineers have been in this industry for over 20 years and served some of the most famous customers from all over the world.We can provide below services for all our partners in this challenging world.1.Fast delivery,1~5 days delivery time for CHXDEV Products.2.Small MOQ requirements for all our items, 1PCS is also acceptable.3.Exclusive Partnership in different regions4.OEM&ODM Design services for bright ideals.5.Free samples avaiable for partners.All our items are coming with CE certification and we have special team work for after sales services 7*24 to help you solve any kind of problem.We are ready for sign contract with you in case you need it, as honest dealer, we never crook our customers.Come and let us make a difference together !