Dixell Digital Refrigeration Controller
Brand Name:Dixell
Certification:EAC
Model Number:XR06CX-5N0C1
Minimum Order Quantity:5 sets
Delivery Time:4-6 weeks
Payment Terms:T/T
Contact Now
Add to Cart
Active Member
Location:
Shenzhen China
Address:
6F Building No.2 Huamei Industry Zone,Jingnan Road,Buji Town,Longgang Disctrict,Shenzhen,China
Supplier`s last login times:
within 1 hours
Product Details
Company Profile
Product Details
Orginal Dixell Digital Refrigeration Controllers XR06CX-5N0C1 With Defrost And Fan Management For Coldroom And Freezer
GENERAL DESCRIPTION
The XR06CX, format 32 x 74 x 60 mm, is microprocessor based
controller, suitable for applications on medium or low temperature
ventilated refrigerating units. It has three relay outputs to
control compressor, fan, and defrost which can be either electrical
or reverse cycle (hot gas). The device is also provided with 2 NTC
probe inputs, the first one for temperature control and the second
one to be located onto the evaporator, to control the defrost
termination temperature and to managed the fan and it’s provided
with a configurable digital input. With the HOTKEY it’s possible to
program the instrument in a quick and easy way.
SPECIFICATIONS / MODELS
| XR01CX | XR02CX | XR03CX | XR04CX | XR06CX | |
| Dimension | |||||
| 32*74*50mm | √ | √ | √ | √ | |
| 32*74*60mm | √ | ||||
| Power supply | |||||
| 12,24V ac/dc (± 10%) | √ | √ | √ | √ | √ |
| 115,230V ac/dc (± 10%) | √ | √ | √ | √ | √ |
| Temperature sensor | |||||
| Coldroom Temp Probe NTC / PTC | √ / optional | √ / optional | √ / optional | √ / optional | √ / optional |
| Defrost / Fan Probe NTC / PTC | √ / optional | √ / optional | √ / optional | √ / optional | √ / optional |
| Function digital signal input | √ | √ | √ | √ | |
| Outout | |||||
| Load or compressor | 20A / 8A | 20A / 8A | 20A / 8A | 20A / 8A | 20A / 8A |
| Defrost | Shut down defrost | Shut down defrost | 8A | 8A | |
| Fan | 8A | ||||
| Light / Auxiliary output | 8A | ||||
| Others | |||||
| Hot Key Programming key | √ | √ | √ | √ | √ |
| Heating / Cooling | Heating / Cooling | Heating / Cooling | Heating / Cooling | Cooling | Cooling |
| XR10CX | XR20CX | XR30CX | XR40CX | XR50CX | XR60CX | XR70CX | |
| Dimension | |||||||
| 32*74*60mm | √ | √ | √ | √ | √ | √ | √ |
| Power supply | |||||||
| 12,24V ac/dc (± 10%) | √ | √ | √ | √ | √ | √ | |
| 115,230V ac/dc (± 10%) | √ | √ | √ | √ | √ | √ | √ |
| Display | |||||||
| 3 digital tubes, minus sign,Decimal point,Output status minus sign | √ | √ | √ | √ | √ | √ | √ |
| Temperature sensor | |||||||
| Coldroom Temp Probe NTC / PTC | √ | √ | √ | √ | √ | √ | √ |
| Evaporator Probe NTC / PTC | √ | √ | √ | √ | √ | √ | √ |
| second Evaporator Probe NTC / PTC | √ | √ | √ | √ | |||
| Condenser Probe NTC / PTC | √ | √ | √ | √ | √ | √ | √ |
| Digital input/display probe | |||||||
| Alarm,Trigger Defrost,Auxiliary probe, door switch,Pressure switch | Settable | Settable | Settable | Settable | Settable | Settable | Settable |
| Relay Outout | |||||||
| compressor | 20A / 8A | 20A / 8A | 20A / 8A | 20A / 8A | 20A / 8A | 20A / 8A/16A | 20A / 8A/16A |
| Defrost | 8A | 8A | 8A | 8A/16A | |||
| Evaporator Fan | 5A/8A | 5A/16A | |||||
| Light / Alarm output | 8A | 5A/8A | 8A/16A | ||||
| Others | |||||||
| Hot Key Programming key | √ | √ | √ | √ | √ | √ | √ |
| Serial Interface MODBUS | √ | √ | √ | √ | √ | √ | √ |
DEFROST
Two defrost modes are available through the “td” parameter:
• td=EL → defrost through electrical heater (compressor OFF)
• td=in → hot gas defrost (compressor ON).
Other parameters are used to control the interval between defrost
cycles (id) ), its maximum length (Md) and two defrost modes: timed
or controlled by the evaporator’s probe. At the end of defrost
dripping time is started, its length is set in the dt parameter.
With dt=0 the dripping time is disabled
FANS
With FC parameter it can be selected the fans functioning:
• FC=cn → will switch ON and OFF with the compressor and not run
during defrost
• FC=on → fans will run even if the compressor is off, and not run
during defrost
After defrost, there is a timed fan delay allowing for drip time,
set by means of the “Fd” parameter.
• FC=cy → fans will switch ON and OFF with the compressor and run
during defrost
• FC=oY → fans will run continuously also during defrost.
An additional parameter “FS” provides the setting of temperature,
detected by the evaporator probe, above which the fans are always
OFF. This is used to make sure circulation of air only if his
temperature is lower than set in “FS”
FANS AND DIGITAL INPUT
When the digital input is configured as door switch iF=do, fans and
compressor status depends on the dC parameter value:
• dC=no → normal regulation;
• dC=Fn → fans OFF;
• dC=cP → compressor OFF;
• dC=Fc → compressor and fans OFF.
When rd=y, the regulation restart with door open alarm.
FRONT PANEL COMMANDS
HOW TO SEE THE SET POINT
1.Push and immediately release the SET key, the set point will be
showed;
2.Push and immediately release the SET key or wait about 5s to
return to normal visualisation.
HOW TO CHANGE THE SETPOINT
1.Push the SET key for more than 2 seconds to change the Set point
value;
2.The value of the set point will be displayed and the “°C” or “°F”
LED starts blinking;
3.To change the Set value push the or arrows.
4.To memorise the new set point value push the SET key again or
wait 10s.
HOW TO START A MANUAL DEFROST
Push the DEF key for more than 2 seconds and a manual defrost will
start
HOW TO CHANGE A PARAMETER VALUE
To change the parameter’s value operate as follows:
1. Enter the Programming mode by pressing the SET+keys for 3s (“°C”
or “°F” LED starts blinking).
2. Select the required parameter. Press the “SET” key to display
its value
3. Use ↑ or ↓ to change its value.
4. Press “SET” to store the new value and move to the following
parameter.
To exit: Press SET+↑ or wait 15s without pressing a key.
NOTE: the set value is stored even when the procedure is exited by
waiting the time-out to expire.
ALARM SIGNALLING
Mess. Cause Outputs
"P1" Room probe failure Compressor output according to “Cy” e “Cn”
"P2" Evaporator probe failure Defrost end is timed
"HA" Maximum temperature alarm Outputs unchanged
"LA" Minimum temperature alarm Outputs unchanged
“EA” External alarm Outputs unchanged
“CA” Serious external alarm All outputs OFF
“dA” Door Open Compressor and fans restarts
Dixell Digital Refrigeration Controller
Inquiry Cart
0