

Add to Cart
Fire Detector Carbon Monoxide Alarm With Digital LCD Display And
LED Index Light
Product Introduction
Carbon Monoxide Detector(CO detector), use of high quality
electrochemical sensors, combined with advanced electronic
technology and sophisticated technology made of a stable work, long
life and other advantages; can be placed on the ceiling or wall
mount and other installation methods, simple installation, easy to
use; Where carbon monoxide gas is present, once the concentration
of carbon monoxide gas reaches the alarm setting value, the
detector will emit an audible and visual alarm signal to remind you
to quickly take effective measures to effectively avoid the
occurrence of fire, explosion, suffocation, death and other
malignancies.
WARNING: Exceeding the temperature and humidity allowable range may
reduce or lose the
detection function.
Specification
Product name | Fire Detector Carbon Monoxide Alarm With Digital LCD Display And LED Index Light |
Alarm current | Less than 70mA |
Product size | 106*37.5mm |
Alarm Volume | >85 dB(A) at 3 meters |
Standby current | Less than 10uA |
Supply voltage | DC4.5V(3×1.5V DC PKCELL AA Battery) |
Low Battery | Less than 3.6V |
Alarm Method | Sound,Lighting Alarm |
Max lifetime | 7years |
Comply to Standard | EN50291-1:2010+AI:2012 |
Instructions
(1) The positive and negative poles of the battery are correctly
inserted into the detector, the buzzer beeps, and the detector
starts to warm up for 40s. The LCD screen displays the countdown,
and the detector has no detection function at this time; after 40s,
the detector enters the normal monitoring state, and the LCD screen
is normally closed. When the measured value of the measured gas in
the air is greater than 20×10-6, the LCD displays the concentration
of the measured gas in the environment in real time.
(2) When the concentration of the measured gas in the environment
reaches the alarm setting value, the detector will send out an
audible and visual alarm indication.
(3) The green power indicator flashes once every 35 seconds,
indicating that the detector is working normally.
(4) Red alarm indicator. When the detector enters the alarm state,
the red alarm indicator flashes quickly and the buzzer sounds. The
alarm cycle of the alarm signal is 4 cycles, each cycle is 100ms
on/100ms off. Then turn off for 2 seconds until the CO
concentration drops below the alarm setting value.
(5) This CO alarm has an automatic self-checking function to detect
hardware failures. In normal standby mode, self-checking is
performed every 1 minute.
How To Install The Co Alarm
This CO alarm is powered by three LR6 AA batteries and requires no
additional wiring. Make sure the alarm can be heard from all
sleeping areas or place several alarms.Install the alarm in places
easy to test and operate and to replace batteries. At the time of
fixing the alarm on the wall, the installation height must be over
1.5m and 0.3m lower than the ceiling, with 1.5m away from room
corners, wall edges and large furniture.
Wall Mounting Installation Steps
1)Having established the mounting location ensure that there is no
electrical wiring or pipe work in the area adjacent to the mounting
surface.
2)Mark the two mounting hole locations in a wall 5.5cm (2.165in)
and drill holes in the marked position. Insert wall plugs into the
holes.
3)Lock the mounting bracket with the screws. Tighten the screws
properly.
4)Insert three AA batteries in the battery compartment with correct
polarity mark on the rear of the detector. After a beep, close the
battery cover, and then test whether the alarm is functioning
properly by press the “TEST” button on the flank of the detector to
make sure it is normal functioning.
5)Clip in the alarm into the mounting bracket.
CAUTION: for safety of the user the CO alarm cannot be mounted
without its batteries. When replace the battery, test the alarm to
make sure it is normal functioning.
Package includes
1 × Carbon monoxide alarm
1 × Mounting bracket
1 × Screw Kit
1 × User manual
FAQ
Q:How about the quality of Carbon Monoxide Detector Alarm?
A :We produce every product with good quality materials and fully
test three times before shippment. What is more, our quality
areapproved by CE RoHS SGS & FCC, IOS9001, BSCI.
Q: Can i have a sample order?
A: Yes, we welcome sample order to test and check quality. Mixed
samples are acceptable.
Q: What is the lead time?
A: Sample needs 1 working days, mass production needs 5-15 working
days depends on order quantity.
Q: Do you offer OEM service, like make our own package and logo
printing?
A: Yes, we support OEM service, including customizing boxes, manual
with your language and printing logo on the product etc.
Q: Can I put order with PayPal for a fast shipment?
A: Sure, we support both alibaba online orders and Paypal, T/T,
Western Union offline orders. Please contact us for details.
Q: How do you ship the goods and how long does it take arrive?
A:We usually ship by DHL(3-5days), UPS(4-6days), Fedex(4-6days),
TNT(4-6days), Air(7-10days), or by sea(25-30days)at your request.