Introduction:
Airflow charcoal making machine, which adopts advanced hot flue
carbonizing technology, is one of our latest developed products.
Modern-designed airflow charcoal making machine greatly increases
carbonizing ratio from about 88% to 99%, and shortens carbonizing
time (from 24 to 6 hours). Also this airflow charcoal making
machine is characterized by easy operation, safety, efficiency,
energy saving and environment protection.Inner pots of airflow
charcoal making machine for charcoal production can be hanged
outside, which will save a lot of cooling time, so the productivity
increases greatly. It is the ideal choice for charcoal production
plant.
The new environmentally friendly horizontal airflow carbonization
furnace adds a flue gas recovery device on the basis of the
original carbonization furnace. After the flue gas is recovered, it
can be dust-free and smoke-free. The recovered flue gas can be
ignited like liquefied gas for heating, cooking, and Dryer use. At
present, there are three types of carbonization furnaces, common
type (can only be used to produce charcoal, not to collect gas);
wood carbonization equipment (used to carbonize branches, wood
blocks, coconut shell blocks, scrap pieces in furniture factories,
etc.) This equipment can be configured The gas recovered by the
gasification furnace device can be turned into fuel gas for the
carbonization furnace's own use or other); the new horizontal
environmentally friendly carbonization furnace has the effect of
one machine and two purposes, and the materials can also be
directly carbonized, or can be carbonized after rods.
| model | 120 | 170a | 170b | 190 |
| capacity | 2T/24h | 4T/24h | 7T/24h | 10T/24h |
| dimension | 2.86*1.6*2.1m | 2.85*2.1*2.1m | 4.60*2.1*2.1m | 5.5*2.2*2.2m |
| weight | 1.68T | 3T | 3.5T | 6.8T |
| inner pot diameter | 1.2m | 1.7m | 1.7m | 1.9m |
| inner pot length | 2.6m | 2.2m | 4.4m | 5.3m
|
The main features of the new horizontal jet carbonization furnace:
①Continuity of production
②Good sealing performance
③The water cooling replaces the traditional natural cooling.
④Composite materials with high heat transfer and wear resistance
form a highly efficient carbonization chamber
⑤All gas is returned to the furnace for combustion without waste
gas pollution
To improve the design of the charcoal carbonization furnace, in
order to prevent gas leakage, the oven door with graphite packing
seal, greatly enhancing the effect of carbonization
In the carbonization process ,can produce combustible gas,can
recycle these gas.These gas delivery to the white tank through No.1
pipeline,then open the valve of the No.2 pipeline, these gas can
reach to the bottom of the furnace through the No.2 pipeline.At the
No.4 valve, you can be connected to a pipeline at the No.4 valve,
so that can use the extra gas,these gas can cooking, burnning
boiler etc.So can save some cost, it is energy saving.
This is shunt tank, at the Nbottom(NO.5) can collect the wood tar.
Raw Materials:
Sawdust, Crops Straw(corn stalk, beanstalk, broomcorn stalk, cotton
stalk, rape stalk,palm kernel shell, groundnut stem, sunflower
stalk), Husk, Grass, Bush branches, Bamboo butt, Bamboo scraps,
Bagasse and so on.
Carbonization stove:
The carbonization stove is a new designed machine for chargin the
wood briquette, bamboo, wood log, coconut shell and so on into
charcoal. It is selling well for its easy operating, high capacity,
good quality. Once carbonization need 8 hours, smokeless and the
raw materials can be wood log or other flammable goods.
The whole line of making wood briquette charcoal
1.Crush the raw material into small pieces (diameter is about
3-5mm);
2.Dry the material by machine or dried it in the sun , till the
moisture is less than 12%;
3.Put the material into feed let of briquette machine;
4.Produce the briquette stick from biomass material without any
additive;
5.Carbonized the briquette stick.
