

Add to Cart
8.2rpm Heating Area Double Cone Rotary Vacuum Dryer For Glycol Ether
DCRD double cone vacuum dryer is a new type of drying equipment
which combines similar product technologies at both home and
abroad. This rotary vacuum dryer possesses a belt and chain
two-stage elastic connection modes. With a low center of gravity,
this drying machine can operate smoothly. Heating medium and vacuum
system adopt reliable mechanical seal or rotating joint, so as to
avoid defects such as the regular packing seal are easy to leak. On
this basis, we modify this double cone vacuum dryer. It not only
embodies the humanized design concept but also meets the GMP
standards.
Biconical rotating vacuum dryer is the dryer suitable for ultra
vacuum drying of all kinds of humid, crystalline and amorphous
products.
Fully heated and insulated drum, rotating at low speed under high
vacuum, continuously renovating the product in contact with the
heated walls.
Working Principle
In order to achieve rapid drying at low temperatures, including the
drying of deep pores, in a way that does not damage the product,
specialized drying technology – vacuum drying – must be used.
The complete product will move into the chamber. The pressure
reduces for so long the saturated steam tension is reached. The
water will discharge through the vacuum chamber from that point.
The raw material is charged in batches & is subjected to
indirect heating while at the same time undergoing rotary motion of
the cone assembly. The double conical shape of the dryer ensures
efficient circulation of hot liquid heating media. Drying takes
place when heat flows from the outer cone through a jacket, and
vacuum is applied in the inner cone. The drying operation is based
on the principle that water or other volatile product moves from a
zone of low pressure. This is accomplished by warming the product
to be dried to raise the vapor pressure of the absorbed or free
liquid by vacuum or by sweeping it with Air or Nitrogen current.
Thus the essential conditions for effective drying are achieved by
uniform heat transfer throughout the batch and rapid removal of the
vapor. The vacuum is applied gradually with PLC control by
throttling.
Most times the specific heat from the evaporating product is lower
than from the base material. This material ensures that the
temperature will drop slowly or even not. The pressure (vacuum)
will achieve any part of the product so the moisture will
evaporate. For a short period there results in a homogeneous
temperature.
Product Application
The drier is suitable for drying and mixing powder or granule raw
material of pharmaceutical industry, foodstuff industry and
chemical industry and so on. Especially it is suitable for the
folliwing raw materials that have special requirements:
Thermal sensitive raw material that can not in high temperature;
Raw materials that are easy to be oxidezed or to be dangerous;
Raw materials in which the solvent needs to recover and there is
toxic gases;
Raw material that have the requirement of containing rather Iow
content of residue volatized materails;
Raw materials that need to mix evenly and fully.
Product Features
1. This rotary vacuum dryer has advanced design, simple internal
structure, convenient to clean and easy to handle.
2. The tubes of heating medium and vacuum system are built in the
rack in order to prevent artificial demage and difficult clean.
3. The outer wall and rack sealing plate adopt polishing treatment,
and the inner container adopts mirror polishing treatment.
4. The materials in the double cone vacuum dryer can be rotated due
to the revolution of the machine, which can minimize material water
content (≤0.5%).
5. The materials will not stick to the wall of the container. With
big drying rate and energy saving, this rotary vacuum dryer can
uniformly and sufficiently dry the materials.
6. Condenser and recycling tank are equipped for recovering organic
solvent.
7. Our double cone vacuum dryer has three types of heat source,
including steam, hot water and conduction oil.
Technical Parameters
Model | 100 | 350 | 500 | 750 | 1000 | 1500 | 2000 | 3500 | 4500 | 5000 |
Volume inside of tank(L) | 100 | 350 | 500 | 750 | 1000 | 1500 | 2000 | 3500 | 4500 | 5000 |
Max loading capacity(L) | 40 | 140 | 200 | 300 | 400 | 600 | 800 | 1400 | 1800 | 2000 |
Max loading weight(kg) | 20 | 70 | 100 | 150 | 200 | 300 | 400 | 700 | 900 | 1000 |
Revolution(rpm) | 3-13 | 6 | 5 | 4 | 4 | 4 | ||||
Heating area(M2) | 1.1 | 2.3 | 2.8 | 3.9 | 5.1 | 6.5 | 8.2 | 12.2 | 16.5 | 18.2 |
Motor power(kw) | 0.75 | 1.1 | 1.5 | 2.2 | 3 | 4 | 5.5 | 7.5 | 11 | 15 |
Occupied area(mm) | 2160*800 | 2160*800 | 2350*800 | 2560*1000 | 2860*1300 | 3060*1300 | 3260*1400 | 3760*1800 | 3960*2000 | 4400*2500 |
Rotating height(mm) | 1750 | 2100 | 2250 | 2490 | 2800 | 2940 | 2990 | 3490 | 4100 | 4200 |
Design pressure of tank(Mpa) | -0.1~0.15 | |||||||||
Desing pressure of jacket(Mpa) | <0.3 | |||||||||
Weight(kg) | 800 | 1100 | 1200 | 1500 | 2800 | 3300 | 3600 | 6400 | 7500 | 8600 |
Schmatic of Installation
Product Show
electrical, steam, natural gas or other