Accessories Mechanical Strength Impact Test Apparatus For EV Testing IEC 60309-1
Brand Name:Sinuo
Certification:Calibration Certificate (Cost Additional)
Model Number:SNQC1008
Minimum Order Quantity:1
Delivery Time:30 Days
Payment Terms:T/T
Contact Now
Add to Cart
Verified Supplier
Location:
Guangzhou Guangdong China
Address:
Room 101, 1st Floor, No. 6, Third Street, Pingshan Industrial Zone 511495, Shibi Street, Panyu District, Guangzhou, China
Supplier`s last login times:
within 36 hours
Product Details
Company Profile
Product Details
Accessories Mechanical Strength Impact Test Apparatus For EV
Testing IEC 60309-1
Product Introduction For Accessories Mechanical Strength Impact
Test Apparatus:
The test equipment is designed and manufactured according to
IEC60309-1: 2012 clause 24.2 and figure 7, etc. It is used to
verify the mechanical strength of the vehicle plugs, socket-outlets
and couplers accessories.
The experimental principle is that after the gravitational potential energy is converted into kinetic energy, the equivalent mass impact weights will be freely released at a certain height to achieve the required impact energy.
The mounting bracket can be adjusted in three-axis, front and back, up and down, and left and right, which has strong applicability.
The experimental principle is that after the gravitational potential energy is converted into kinetic energy, the equivalent mass impact weights will be freely released at a certain height to achieve the required impact energy.
The mounting bracket can be adjusted in three-axis, front and back, up and down, and left and right, which has strong applicability.
Technical Parameters For Accessories Mechanical Strength Impact
Test Apparatus:
| Operation Method | Manual operation |
| Impact Weight | 50*16mm; 304# stainless steel 0.25Kg impact weights |
| Combined Impact Weight | 0.5Kg (low energy) (2 pieces of 0.25Kg weights), |
| Impact Energy | 1～6J (The impact weights can be interchangeable) |
| Hammer Anvil | Ф50 mm |
| Impact Angle | 25°, 35°, 36°, 42°, 47°, 52° |
| Pendulum Support Structure | Can move back and forth, left and right, up and do and can rotate 90° |
| Pendulum Material | Steel pipe with outer diameter of 10 mm and wall thickness of 1.0 mm |
| Pendulum Length | 1m, from the pivot to the center of the impact element |
| Mounting Plate | 8mm thick stainless-steel plate, made according to the customer's specified aperture and position, default one set |
| Impact Height | 776mm, 833mm |
| Vertical Backboard Material | Plywood |
| X/Y/Z Axis Stroke | Movable range is greater than 300 mm |
Counterweight and impact energy For Accessories Mechanical Strength Impact Test Apparatus:
Choose the counterweight and drop angle according to the impact
energy. If the impact energy is ≤2J, add two counterweights at the
upper hole position and with one weight on each side, the total
mass is 0.5kg; if the impact energy is >2J, add two more
counterweights at the lower hole position and with two weights on
each side, the total mass is 1Kg.
Counterweights of the impact energy and the impact angle are shown
in following Table:
| Impact energy(J) | Counterweights(Kg) | Release angle |
| 1 | 0.5 | 25° |
| 2 | 0.5 | 35° |
| 3 | 1 | 36° |
| 4 | 1 | 42° |
| 5 | 1 | 47° |
| 6 | 1 | 52° |
Notice For Accessories Mechanical Strength Impact Test Apparatus:
1 No-load impact is strictly prohibited for the device, that is, there should be objects during impacting.
2 The screw must be frequently lubricated to prevent rust.
3 Required environmental conditions: temperature 5℃~35℃, humidity 45%~75%.
Accessories Mechanical Strength Impact Test Apparatus For EV Testing IEC 60309-1
Inquiry Cart
0