PCA9635PW LED Lighting Drivers ICs TSSOP-28 400mW 16 Channel

PCA9635PW LED Lighting Drivers ICs TSSOP-28 original in stock

16 LED drivers. Each output programmable at:
◆ Off
◆ On
◆ Programmable LED brightness
◆ Programmable group dimming/blinking mixed with individual LED brightness
■ 1 MHz Fast-mode Plus compatible I2C-bus interface with 30 mA high drive capability on SDA output for driving high capacitive buses
■ 256-step (8-bit) linear programmable brightness per LED output varying from fully off (default) to maximum brightness using a 97 kHz PWM signal
■ 256-step group brightness control allows general dimming (using a 190 Hz PWM signal) from fully off to maximum brightness (default)
■ 256-step group blinking with frequency programmable from 24 Hz to 10.73 s and duty cycle from 0 % to 99.6 %
■ Sixteen totem-pole outputs (sink 25 mA and source 10 mA at 5 V) with software programmable open-drain LED outputs selection (default at totem-pole). No input function.
■ Output state change programmable on the Acknowledge or the STOP Command to update outputs byte-by-byte or all at the same time (default to ‘Change on STOP’).
■ Active LOW Output Enable (OE) input pin. LED outputs programmable to logic 1,logic 0 or ‘high-impedance’ (default at power-up) when OE is HIGH, thus allowing hardware blinking and dimming of the LEDs.
■ 7 hardware address pins allow 126 devices to be connected to the same I2C-bus
■ 4 software programmable I2C-bus addresses (one LED Group Call address and three LED Sub Call addresses) allow groups of devices to be addressed at the same time in any combination (for example, one register used for ‘All Call’ so that all the PCA9635s on the I2C-bus can be addressed at the same time and the second register used for three different addresses so that 1⁄3 of all devices on the bus can be addressed at the same time in a group). Software enable and disable for I2C-bus address.
■ Software Reset feature (SWRST Call) allows the device to be reset through the 2C-bus
■ 25 MHz internal oscillator requires no external components
■ Internal power-on reset
■ Noise filter on SDA/SCL inputs
■ Edge rate control on outputs
■ No glitch on power-up
■ Supports hot insertion
■ Low standby current
■ Operating power supply voltage range of 2.3 V to 5.5 V
■ 5.5 V tolerant inputs
■ −40 °C to +85 °C operation
■ ESD protection exceeds 2000 V HBM per JESD22-A114, 200 V MM per
JESD22-A115 and 1000 V CDM per JESD22-C101
■ Latch-up testing is done to JEDEC Standard JESD78 which exceeds 100 mA
■ Packages offered: TSSOP28

Q: Can you accept small order?
A: Yes,small order is available .Please contact with us.

Q: Do you provide samples,it is free or extra?
A:Yes,we could offer the sample for free charge but do not pay the cost of freight.

Q: Can we get a lower price? Any Discount?
A: Yes,price is not a problem,everything could be negotiated based on the quantity.

Q: Do you provide the BOM Kitting service? Can I send my BOM to you?

A: Yes,Please feel free to contact us and send us your BOM and then we'll quote for you.

Q: What is your lead time?
A: Most of the products can be sent out within 3 days after payment.

Q: How can I place order?
A: You can contact us by email about your order details, or place order on alibaba.

Q: How can I pay ?
A: After you confirm our PI,we will send the order with the payment link to your email,there are several payment way(include TT/VISA/Online bank/credit card,etc. ),you can choose the one you like.

Founded in 2004, Walton Electronics CO.,LTD is a scaled and professional independent distributor of electronic components in Shenzhen , China. Committed to the world's leading brands of electronic components distribution integration services, mainly engaged in active components , integrated circuit chips.

We provide products and services in all areas of the electronics industry, including: automotive, medical, consumer electronics, industrial control, Internet of Things, new energy,communications, military and so on.