4 Cylinder Fuel Injector Cleaner Tester Machine 200ml Volume CE Certificate
Brand Name:Wonderfu
Certification:CE
Model Number:WDF-GDI
Minimum Order Quantity:1
Delivery Time:26 working days
Payment Terms:T/T, L/C
Contact Now
Add to Cart
Active Member
Location:
Guangzhou China
Address:
3rd Floor, No. 6 BLOCK, No.15 Jingu Road, Xiutang Village, Huadong Town, Huadu District, Guangzhou
Supplier`s last login times:
within 1 hours
Product Details
Company Profile
Product Details
Car Ultrasonic Cleaning Machines 4 Cylinder Fuel Injector Auto Tester And Cleaner Tool
Why have to clean injector?
* When we turned off the engine suddenly, the gasoline which have
been spray out can not be recycled. It would attached on the
injector and combustion chamber walls.
* Gasoline is easy to volatile, but wax and varnish were stayed.
* Heat these wax and varnish day after day,they will be changed
into hard coke.
* The hard coke will be produced more quickly and more thickly when
engine work with poor quality fuel.
Fuel Injector Tester is an instrument which can test & measure the injectors' droplet formation, atomization, efficiency and fuel delivery. All are visually and / or physically checked and tested as a starting point, rather than as a last resort. When problems are found, the injectors are cleaned in the supplied ultrasonic cleaning bath. The injectors mount in a special plate and are connected to the tester in order to operate them at high frequency during cleaning. After cleaning, the rubber sealing rings, plastic protection caps and filter baskets can be replaced (as applicable) before re-testing to ensure all the injectors are performing as a perfectly matched, balanced set.
Function:
1. Check the injector starting pressure, Assessment of the injector
spray fog quality, Inspection of the injector spray oil range,the
injector seal and angel and the injector oil flow |
2. The machine has fog dissipation convulsion device to improve the
work condition. |
3. It has two grade filter to ensure the cleanliness of test. |
4. The parameter of common rail injector (fuel spray counts,
frequency, pulse width, pressure etc.) can be set willfully. |
Features:
1. Cleaning hard coke from injector via ultrasonic and auto
electronic technology;
2. Imitate working as vehicle's fuel system;
3. Backwashing;
4. Uniformity testing;
5. Fog detection;
6. Fuel injection quantity detector;
7. Tightness test;
8. Automatic cleaning mode;
9. Vehicle cleaning mode;
10. The minimum pulse width test.
Installation :
1. All equipment are delivered with 3 pin electrical cable, use the ground connection for equipment and operator protection.
2. Verify that test liquid level at 2.5L or at least between the range of two red lines. For a new machine, please fill 2.0~ 2.5L testing liquid. Never fill up the tank at its maximum capacity.
3. Fill up the ultrasonic cleaning tank with the liquid for injector cleaning. Liquid level should not reach 3 cm below the tank edge, in order to avoid liquid overflow on device. Take special care not to drop liquid on the equipment when filling up or emptying the tank.
Techenical Parameter:
Power supply: AC220V±10%, 50/60Hz; AC110V±10%, 50/60Hz.
Input power: 250W;
Ultrasonic cleaner power: 100W;
Simulated RPM range: 10~9990rpm; step: 10rpm;
Time range: 1~9999s;
Pulse width: 0.5~25ms; step 0.1 ms;
Test Liquid Tank Volume: 3L
Power supply: AC220V±10%, 50/60Hz; AC110V±10%, 50/60Hz.
Input power: 250W;
Ultrasonic cleaner power: 100W;
Simulated RPM range: 10~9990rpm; step: 10rpm;
Time range: 1~9999s;
Pulse width: 0.5~25ms; step 0.1 ms;
Test Liquid Tank Volume: 3L
Notice!!!
1) Different test joints are required to test different types of fuel nozzles. This device only provides basic configuration, more configurations of the connector need to be purchased separately.
2) Due to the difference in internal structure, some types of GDI nozzles cannot be temporarily tested.
3) In addition to cleaning the fuel injection nozzle, the ultrasonic device can also clean the small size of fuel pump, spark plug, etc.
Parts, but pay attention to choosing the right cleaning agent.
4) In order to improve the cleaning and test results, please connect compressed air when performing GDI nozzle test and set the air pressure to 6-8 bar
5) If an extension cord is required, a cord with a rated current equal to or greater than the rated current of the device should be used. The wire may overheat when the rated current is lower than the current of the device.
6) The test liquid is used for uniformity/sprayability test, leak test, sample volume test and automatic. test. Detergents are used to clean the combustion chamber. Ultrasonic use special injector cleaner (or equipment Included test liquid and detergent) for cleaning
4 Cylinder Fuel Injector Cleaner Tester Machine 200ml Volume CE Certificate
Inquiry Cart
0