3-30S Li Ion BMS Battery Management System LIFEPO4 With RS485 UART Dual Communication

3-30S li-ion Smart BMS Battery Management System LIFEPO4 with RS485 UART dual communication

What BT Communication Module can do ?

With BT Communication Module , the APP Software can be connected , and all information of the BMS can display on your Mobile Phone . and you can set some parameters on Your APP software :Over-protection voltage , Over-discharge protection voltage ,Rlease voltage of over-charge and discharge

Adjustable BMS can set up Voltage and Current

You could get the SOC, RM, RSOC, Voltage, Current, Temperature of battery pack through UART connect

Please contact with us for more information

Specification:

Warning :
1.Should strictly follow the connection step as the diagram.
2.Double check the connection is correct,then connect it to the battery pack "+","-" Pin.
3.We are not responsible for the defectives caused by wrong connection.

RFQ

1.What is the common port and separate port? what is the difference?
We take 13S 48V 15A BMS as an example, common port 15A means your charge cathode and discharge cathode are connected in the same point end(our P-), charge cathode and discharge cathode are used in the common connection
port, so the charge current and discharge current are the same 15A. while the separate port is separately connected by charge cathode (C-) and discharge cathode (P-), so the charge current and discharge current are different, discharge current 15A, charge current 8A.

2.What is the balance function?
The working principle and function are as followings, when your one cell voltage is upto alarm voltage(Li-ion upto 4.18V, LifePo4 upto (3.6V), then the cell Balance starts to work, balance resistance starts discharge with 35ma(when balance discharge starts to work, BMS will starts a little heat up, which is the normal reflection), the cell is in both charging and discharging status, and others which are not reached to alarm voltage(Li-ion 4.18V, LifePo4 3.6V)are only in charging status, no discharging, when the fast cell voltage is reached to alarm voltage (Li-ion 4.25V, LifePo4 3.75V) BMS starts off power protection, all the other cells are all in stop of charging, this process will enable your battery charging in balance current, and your battery voltage are in balance status, but when your cell voltage difference are in a big range, then balance can not be functionning well

3.The relationship between Battery capacity and BMS current?
There is no direct relationship between Battery capacity and BMS current, big capacity doesn`t mean a big battery, but rely on continue current, that is to say if your engine is powerful, your should choose high current of BMS, it is not relied on battery capacity.

4. What type of charger should I choose?
Lithium battery must choose specific charger, do not use Charger for Leadacid battery, for leadacid charger may have MOS with high pressure breakdown protection, which will not protect of BMS over charge. Life Po4 battery charger voltage=battery string No.X3.6V, while Li-ion battery charger voltage=Battery string No.X4.2V.

5. What current BMS should I choose ?
Take 10S 36V as an example: what current BMS you choose is relied on your E-bicycle Motor power and current limitation of controller. eg., choose 15A for below 350W, 20A for below 500W, 30A for below 800W, 60A for Below 1000W, higher than 1200W are contact with our service specialist for suggestions, one inall, continue current shall be higher than current limitation in Controller.

6. Whether my BMS damaged?
if you want to judge if the BMS is damaged, please take the folowing steps, to test if each cell voltage is the same with
voltmeter? if the cell voltage difference is over 1.0V, the fault is displayed that it cannot run far, no power supply at the
start range, short charge time, all these issues are almost caused by battery cells, if BMS damaged is displyed as no charge, no discharge, no discharge while the battery has voltage.

Shenzhen XUWEN Technology Co.,Ltd is a comprehensive technology company specializing in the research, development, production and sales of various lithium-ion battery packs, lithium battery protection management systems, lithium battery testing equipment . Specializing in the production of power, energy storage, digital and other lithium batteries, lithium iron phosphate battery protection boards.

The company adheres to the principle of "mutual benefit and common development", and welcomes business negotiations and cooperative development. Product introduction: power battery protection board With equalization and temperature control. High-quality MOS tube protection current. Same port installation, simple and convenient.

Intelligent software protection board With CAN/RS485/RS232/RS232/RS422/USART/GPS positioning communication. Can be customized according to customer requirements. Our products are strictly tested in the laboratory. All data comply with CE, FCC, RoHS, ISO certification.